Chuck, I am not sure about the development history of IO-Link. Clearly it was motivated by the need for an inexpensive way to easily set dconfiguration parameters, monitor systems and do troubleshooting of inexpensive devices linked to a fieldbus network. Automation suppliers have widely embraced it for all of those reasons. The overhead and expense of adding Ethernet to these simpler devices, such as sensors, plus the openness of the technology has also played a key role in its gaining support.
Chuck, I think the idea was to have a standard type of communication topoology regardless of the bus structure. Basically, it's due to the many different types of bus out there.
Interesting article, Al. What's the history of IO-Link? Did this grow up in response to Industrial Ethernet, or did it exist in some other form previously?
apresher, the important thing is that Ethernet brings a lot of advantages to the industrial environment, while having a different structure than networking protocols that were designed for that environment. The idea of a two tier approach, with another protocol handling the shorter distance, lower speed aspects of the last foot, is almost inevitable. With the availability of standardized modules that interface these other bus technologies with Ethernet, a system can be created that easily handles modules with different protocols in the same system. As long as the programmer can treat these as I/O points on the Ethernet network, then various suppliers can be used without unduly restricting the design. This is the essence of the systems approach.
Helge, Excellent discussion and analysis. The point is that these technologies can extend networking functionality at low cost the last foot, and provide a way to increase the intelligence of these devices without costs especially for setting parameters, configuration and diagnostics. Thanks.
It is important to clearly separate IO-Link and whatever Ethernet based protocol a user might select. While IO-Link adds functionality and diagnostics capability to an "end device" it is still, as was pointed out, a parallel wiring technology and does therefor not simplify installations using Ethernet. As was pointed out the overhead associated with Ethernet is significant. This makes it necessary for Ethernet field I/O to have a relatively high I/O count; perhaps 16 or 32 I/O points per module. IO-Link is not going to change that fact. Considering applications in material handling or storage and retrieval such a high I/O count results in setting up an Ethernet network PLUS a significant parallel (i.e. hardwired) cabling to the sensors and actuators. IO-Link or not, the extra material (cordsets, wiring duct ...) needed is still considerable. In those cases a highly decentralized solutions like AS-Interface offers better functionality, faster installation, reduced material and ultimately lover cost. And since AS-Interface makes use of a proven installation piercing technology adding low density I/O wherever necessary is possible. It should also be mentioned that AS-Interface does not replace Ethernet. On the contrary, users selecting any Ethernet solution will simply add the appropriate gateway and then collect field I/O through low density/ low cost I/O modules (some are as little as a book of matches.) From the PLC's point of view a gateway is simply an Ethernet I/O module with hundreds of I/O points.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
