HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Page 1/2  >  >>
William K.
User Rank
Platinum
Re: Gesture sensors and industrial robots: Deadly?
William K.   9/21/2013 9:08:49 PM
NO RATINGS
You certainly are correct. I hope that others see the wisdom in selecting mechanical methods for the "E-Stop" function.

taimoortariq
User Rank
Gold
Re: Gesture sensors and industrial robots: Deadly?
taimoortariq   9/21/2013 1:46:06 AM
NO RATINGS
Gesture control although a very useful and efficient solution to many engineering problems, might not fit here. Because in emergency situation to have a direct mechanical control is most reliable. There might be alot of safety precautions with gesture control as well, but it is always safer to have a direct emergency control that requires some mechanical action, it is almost always trustworthy.

William K.
User Rank
Platinum
Gesture sensors and industrial robots: Deadly?
William K.   9/24/2012 6:31:23 PM
NO RATINGS
I can see that an industrial robot that would run the program based on a gesture for a start command could be safer, and possibly even better. BUT as an engineer responsible for safe operations I would NEVER consider leaving out the big red EMERGENCY STOP button. Adding a gesture input in addition would be OK, but to put something as important as an emergency stop function on the wrong end of a lot of software would be very irresponsible. JUst remember those cars with thatbSTUPID start/Stop button that does not work in an emergency situation. There is a very valid reason that E-Stop is not done in software.

Jon Titus
User Rank
Blogger
Re: Languages not the problem
Jon Titus   9/24/2012 3:11:12 PM
NO RATINGS
OK, mrdon.  Some MCU manufacturers offer wizards to help programmers configure the bits and bytes through a graphical interface.  The Texas Instruments "GRACE" software, for example, provides this capability for some of the MSP430 processors.  A programmer selects the necessary peripheral devices and then selects the desired settings. GRACE creates C-language source code to do the job.

mrdon
User Rank
Gold
Re: Languages not the problem
mrdon   9/24/2012 2:16:42 PM
NO RATINGS
Hi Jon, I agree. Just appealing to the small group of assembly language coders who might be reviewing the comments.

Jon Titus
User Rank
Blogger
Re: Languages not the problem
Jon Titus   9/24/2012 2:04:15 PM
NO RATINGS
Hi, mrdon.  I bet bit-bashing code in assembly language provides only a small time advantage over code written in C and compiled.  Current compilers provide optimizations and can get very "close" to an MCU's hardware for control. I would much rather read control code in C than try to figure out bit configurations and settings in another programmer's assembly-language code. (Been there, done that!)

Jon Titus
User Rank
Blogger
Re: Gesture sensors and industrial robots: Deadly?
Jon Titus   9/24/2012 2:00:08 PM
NO RATINGS
Hi, William.  People would train robots to respond only to specific gestures.  Thus, someone couldn't use an industrial robot to follow his or her every move and start tearing apart an assembly line.  Gesture control would require security to prevent unauthorized use or "training."

Jon Titus
User Rank
Blogger
LabVIEW Does Gesture Control
Jon Titus   9/24/2012 1:56:26 PM
NO RATINGS
By the way, LabVIEW code has demonstrated the capability to use gestures for control operations. The application uses 3-D vision.

Jon Titus
User Rank
Blogger
Re: Languages not the problem
Jon Titus   9/24/2012 1:54:05 PM
NO RATINGS
Hi, Naperlou, et al.  LabVIEW creates compiled code.  It does not create some sort of intermediate code that requires an interpreter.  Instead, you get native code that runs on your target processor.  And as far as I know, you can mix in C-language code, too, if you need to do something at that level.  Also, LabVIEW will compile and run applications in FPGAs.

mrdon
User Rank
Gold
Re: Languages not the problem
mrdon   9/23/2012 9:52:20 PM
NO RATINGS
Nancy Golden, Using assembly language with gesture controls may improve response time because of the software being one level above machine code. Therefore, bit processing is closer to the target microcontroller than a high level language like "C" code. Just thinking out loud folks!

Page 1/2  >  >>


Partner Zone
Latest Analysis
Some of our culture's most enduring robots appeared in the 80s. The Aliens series produced another evil android, and we saw light robot fare in the form of Short Circuit. Two of the great robots of all time also showed up: The Terminator and RoboCop.
Two students have created a voice-command system for our homes, based on the simple and affordable Raspberry Pi.
Optomec's third America Makes project for metal 3D printing teams the LENS process company with GE Aviation, Lockheed, and other big aerospace names to develop guidelines for repairing high-value flight-critical Air Force components.
This Gadget Freak review looks at a cooler that is essentially a party on wheels with a built-in blender, Bluetooth speaker, and USB charger. We also look at a sustainable, rotating wireless smartphone charger.
Texas Instruments is rolling out a new microcontroller that could make the design of sensor networks and data logging systems simpler and less costly.
More:Blogs|News
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 4 - 8, Introduction to Linux Device Drivers
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: August 12 - 14
Sponsored by igus
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service