HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
REGISTER   |   LOGIN   |   HELP
Page 1/5  >  >>
armorris
User Rank
Platinum
Re: Company confidential information
armorris   10/31/2012 11:12:46 AM
NO RATINGS
Here is a much more readable version of the patent application on my motor speed regulator. Google Patents is great! No TIFF viewer is needed and you can download a PDF version of it.

http://www.google.com/patents/US20030107341

 

Cadman-LT
User Rank
Platinum
Good solution
Cadman-LT   10/8/2012 1:43:04 PM
NO RATINGS
Nice gadget! That's a good solution for cheap rotary tools without speed control.

armorris
User Rank
Platinum
Re: Resolved overload protection issue
armorris   9/25/2012 12:48:15 PM
NO RATINGS
Before this article was published, when I added R10, I sent the editor an updated pdf file and for some reason, the first pdf file was published. I have resent the corrected file twice and it has not been posted. R10 is a 22k resistor connected between Q2's drain and ground. Please email me if you would like the updated pdf file.

William K.
User Rank
Platinum
Re: Speed control for rotary tool
William K.   9/24/2012 9:03:18 PM
NO RATINGS
Mrdon, the motor controller had one section of a 556 generating a triangle wave from 1/3 Vcc to 2/3 Vcc, the other section used a potentiometer to vary the reference for the second section that is used as a comparator. The signal from the comparator feeds a small transistor that drives a TO-3 power transistor. 

The circuit to generate the PWM signal came from an applications note. So it is really not anything that complex. I may be able to find a copy of the circuit someplace in my archives, but that may take a while.

William K.
User Rank
Platinum
Re: Speed control for rotary tool
William K.   9/24/2012 6:06:45 PM
NO RATINGS
OK, it was a variable speed drive. What we used for feedback was the effect of the pump delivery rate, which was controlled by the motor speed. It was not clear that any feedback was used with the tool speed controller, either. Small tools seem to work better if they do slow as the load increases. 

The other thing is that a motor controlled with PWM may not have as much speed drop as the load increases, since PWM control does not increase the source impedance.

armorris
User Rank
Platinum
Re: Handy project!
armorris   9/24/2012 2:47:44 PM
NO RATINGS
BTW, Myke Predko's name is spelled "Myke". I have two of his books and I verified it.

armorris
User Rank
Platinum
Re: Speed control for rotary tool
armorris   9/24/2012 8:23:17 AM
NO RATINGS
William K. Thanks for your response. Was your device a controller or a regulator? In other words, how did you sense the motor speed? I can build a DC motor controller with a 555 timer, a pot, a MOSFET and a few small components. Such a device would not be a speed regulator as it would have no feedback.

mrdon
User Rank
Gold
Re: Handy project!
mrdon   9/23/2012 9:16:43 PM
NO RATINGS
When it comes to learning PIC microcontrollers, Mike Predko is an excellent teacher. I have several PIC microcontroller books by Mike and his writing style make developing microcontroller applications a breeze. His books also provide solutions on debugging software errors as well.

mrdon
User Rank
Gold
Re: Speed control for rotary tool
mrdon   9/23/2012 9:07:09 PM
NO RATINGS
William K, It would be interesting to see the circuit schematic diagram of your design. Sounds like a possible Gadget Freak article to me!

William K.
User Rank
Platinum
Speed control for rotary tool
William K.   9/23/2012 5:51:58 PM
NO RATINGS
In 1979 I designed an inexpensive PWM speed controller for use with a 12 volt DC motor. The control kept the torque at maximum because of not having a voltage drop, other than the Vce of the switching transistor. And the design was not patentable, so I was home-free there as well. It use a 556 dual timer chip with one section as an oscillato9r and the other section as a comparator for the ramp waveform and the setpoint voltage. One intermediate transistor buffer stage and it drove a 100 volt 5 amp switching transistor, which I don't recall the number. The BOM cost, except for the control pot, was just under $5. Probably all of the parts are still available, and there is probably a much better output transistor available today. Possibly even a FET of some type.

Page 1/5  >  >>


Partner Zone
Latest Analysis
These are the toys that inspired budding engineers to try out sublime designs, create miniature structures, and experiment with bizarre contraptions using sets that could be torn down and reconstructed over and over.
Connected sensor-enabled applications will improve the consumer experience -- and generate new revenue streams.
PowerStream is deploying the microgrid at its headquarters to demonstrate how people can generate and distribute their own energy and make their homes and businesses more sustainable through renewables.
Printrbot unveils its all-metal Printrbot Simple, bringing durability to low-cost 3D printers.
Today's robots should be respected, and humans should be wary of their growing skills and sophistication. Quite simply, robots are better than us in a lot of ways. Here are 10 of them.
More:Blogs|News
Design News Webinar Series
3/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
2/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
12/18/2013 Available On Demand
11/20/2013 Available On Demand
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Apr 21 - 25, Creating & Testing Your First RTOS Application Using MQX
SEMESTERS: 1  |  2  |  3  |  4  |  5


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: April 29 - Day 1
Sponsored by maxon precision motors
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service