Straight gas is definitely better than the ethanol blend for hand held power equipment. There is another option available. STIHL offers Motomix pre blended fuel that utilizes ethanol free high octane gas pre-mixed at 50:1 ratio for use in hand held power equipment. It runs great in their product.
Yes Rob, it eats most anything made from rubber. By the looks of it, the rubber becomes brittle, then just falls apart. Now for "negative consumer reaction to legislation". Who will Congress pay more attention to; a) a guy on a remote island with a few hundred dollars in damaged tools or b) a lobby guy who plunks a million dollars on his desk for reelection?
Same with sugar, Americans pay way more than the international price, but most folks think they don't use enough sugar to whine about the few cents more they pay. To us, its a few cents, to big sugar, its millions. Lobbists pay Congressmen to support bills like the ethanol scam. Demand for corn increases, prices of food increase, the ethanol business is subsidized by tax dollars, the Federal Reserve prints ever more money driving prices even higher and the resultant comments are: It's those damn Arabs!
I don't know about you, but certaily I don't count much to my Congressman. I send them a letter, I get a form letter back that has nothing to do with my topic (other than he is working/fighting hard for me), and we end up paying for the postage (franking). What a system. The best government money can buy.
I'd like to turn the political clock back 200 years.
This story is a good example of environmental stress cracking, which I covered in an article earlier this year. Evaluating the resistance of rubber and plastic materials to new biofuels helps keep materials engineers like me busy. Besides ever-increasing ethanol percentages (your product had better be able to tolerate gasoline containing 25% ethanol if you want to sell it in Brazil!), there are also newer alternative fuels and fuel additives such as biobutanol that need to be considered.
As Beth points out, it's important to keep up on these trends, and make sure that the materials in your product will be compatible.
I am in Royal Oak, two blocks south of the Red Run golf course.
I investigated the engineering program at Oakland University in 1969, and based on what I saw, I enrolled in the Lawrence Technical Institute instead. I graduated with a BSEE and have been in engineering ever since.
And, based on the several jobs and employers that I have had over the years, I suspect that the engineering salary surveys that I have seen are a bit exagerated. Or at least, they don't include this part of the country. How reliable is that data, and have you ever seen the tax returns to verify it's veracity?
Hey, I had a lawnmower that kept wearing out carburator parts. I wonder if it was the ethanol? I just blamed the design and rebuilt the carb every couple years.
Yes, I would imagine it would be hard to find gas stations that sell non-ethanol gas. Even with the directory mentioned in earlier comments, I would guess those stations come and go. By the way, William, where are you in southeastern Michigan. I grew up near Oakland University.
We don't see consumer backlash because the link between the damage and the cause of the damage is not that obvious. Around this part of southeastern Michigan it is hard to find gas that does not have ethanol added. They add ethanol because then water will disolve in the fuel and water is much cheaper. So the profit increases. The downside is that the mix is a bit corrosive, so not only is there an ethanol damage problem, but also a larger corrosion problem. The mix conducts electricity, while pure gasoline does not conduct.
It is amazing how many ways our modern materials can be damaged- sun, chemicals, ethanol gasoline, and so on. Short sighted engineers can cause problems in the field where a little common sense and consulting could resolve them before they happen.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
Researchers at MIT and Sandia National Labs have observed a reaction in lithium-air batteries that could help improve the design of these cells for electric vehicles and other applications.
Healthcare might seem to be an unlikely target application for the Internet of Things technology, but recent developments show small ways that big-data is going to make an impact on patient care moving into the future.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
