HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 3/3
Ann R. Thryft
User Rank
Blogger
How real are combustion engine breakthroughs?
Ann R. Thryft   9/19/2012 12:44:50 PM
NO RATINGS
I, too, was intrigued by the Combustion Engine Breakthrough category. The main example DuPont gave is Ford's EcoBoost engine, which we've covered before, and it's not at all fairy-dust: http://www.designnews.com/author.asp?section_id=1387&doc_id=234102 http://media.ford.com/images/10031/EcoBoost.pdf Then there are several slides in Chuck's slideshow yesterday that address engine improvements, such as slide 3 on Toyota's D-S4 engine, slide 6 on Chevy's Ecotec, slide 15 on Fiat's Multi-Air inline engine, slide 16 on engine active fuel management, and slides 8 and 11 on the GDI technique, which sounds to me like a real breakthrough at up to 30% consumption reduction potential.

Ann R. Thryft
User Rank
Blogger
Re: Tires didn't make the list
Ann R. Thryft   9/19/2012 12:43:14 PM
NO RATINGS
TJ, if you look at the pie chart, you'll see that there's an Other category that comprises 4% of responses, as well as an Aerodynamics category at 1%, one (or both) of which may have included tire improvements. Whatever improvements they add apparently weren't statistically large enough, in the context of the others, to justify a separate category, at least in the minds of these respondents. That said, as you rightly point out there are many improvements shown in Chuck's slideshow yesterday that can be done, and that fall outside the big three categories in this study.

Ann R. Thryft
User Rank
Blogger
Re: getting the weight down
Ann R. Thryft   9/19/2012 12:42:39 PM
NO RATINGS
Lou, that balance between adding safety features and saving weight is top of mind for automotive engineers and the car companies in general, and for materials makers like DuPont, as well as sub-system makers like engine component companies, in particular. Chuck's slideshow yesterday shows a host of these:
http://www.designnews.com/author.asp?section_id=1366&doc_id=250882
Balancing all these tradeoffs requires the type of system-level thinking DuPont is using to develop new materials with its matrix structure, as Beth points out.

TJ McDermott
User Rank
Blogger
Tires didn't make the list
TJ McDermott   9/19/2012 10:14:11 AM
NO RATINGS
I'm surprised they didn't.  Proper pressure and decreased rolling resistance have a measurable impact.  Yesterday's slideshow noted it.

http://www.designnews.com/author.asp?section_id=1366&doc_id=250882&itc=dn_analysis_element&

And is one of the easiest things to do.  Any number of improvements (pressure sensors become standard, on-board compressors to maintain pressure) would immediately improve mileage.

Combustion Engine Breakthrough too much sounds like we're waiting for a genie to grant a wish.

naperlou
User Rank
Blogger
getting the weight down
naperlou   9/19/2012 8:20:53 AM
NO RATINGS
One big trend in automobiles in the last few years has been enhanced safety.  With stronger structures, and specific safety equipment such as air bags, we have become safer in the event of an accident.  The downside is the weight added by all this safety equipment. 

While in the 1970s I had a 1960s car that weighed only 1,400 pounds, there is nothing at that weight available now.  With a heavy and very unsophiscated engine the car could get 40 MPG on the highway.  Of course, it was not very safe. 

So, while looking at ways to cut weight, it woulld be interesting to see if there are ways to use these new material features to enhance safety as well.  I saw an artivle recently that made the comment that were going toward lighter cars, but that would probably compromise safety.  Perhaps this new approach to designing materials will allow companies like DuPont to address both.

Beth Stackpole
User Rank
Blogger
Big-picture engineering
Beth Stackpole   9/19/2012 7:17:00 AM
NO RATINGS
Looks like DuPoint's matrix strategy for materials development will enable it to leverage a lot of intellectual property and design innovative across various core platforms as opposed to reinventing the wheel for every separate endeavor. Great example of big picture, systems engineering thinking as opposed to a one-off strategy around lightweighting.

<<  <  Page 3/3


Partner Zone
Latest Analysis
It's been two years since the Mac Mini's last appearance on iFixit's teardown table, but a newly revised version joins Apple's lineup this week.
More often than not, with the purchase of a sports car comes the sacrifice of any sort of utility. In other words, you can forget about a large trunk, extra seats for the kids, and more importantly driving in snowy (or inclement) weather. But what if there was a vehicle that offered the best of both worlds; great handling and practicality?
Kevin Gautier of Formlabs describes the making of a carbon fiber mold for an intake manifold, using a $3,300 3D printer, during Medical Design & Manufacturing Midwest.
Science fiction author Isaac Asimov may have the best rules for effective brainstorming and creativity. His never-before-published essay, "On Creativity," recently made it to the Web pages of MIT Technology Review.
Much has been made over the potentially dangerous flammability of lithium-ion batteries after major companies like Boeing, Sony, and Tesla have grappled with well-publicized battery fires. Researchers at Stanford University may have come up with a solution to this problem with a smart sensor for lithium-ion batteries that provides a warning if the battery is about to overheat or catch fire.
More:Blogs|News
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 20 - 24, How to Design & Build an Embedded Web Server: An Embedded TCP/IP Tutorial
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: 10/28-10/30 11:00 AM
Sponsored by Stratasys
Next Class: 10/28-10/30 2:00 PM
Sponsored by Gates Corporation
Next Class: 11/11-11/13 2:00 PM
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service