I wasn't just talking about airbags. U.S. cars have many other safety devices vs Nanos, not including the new electric nannies, including better bumpers, side beams in doors, collapsing steering columns, safety glass, and more than one windshield wiper. 624cc rear mounted 2 cylinder engine, 3 lug nuts per wheel, zero to 37mph in 8 seconds will make other drivers happy. Top speed is 65, which is not safe on most U.S. 60mph freeways. Get in an accident in a Nano and you will get hurt. Just like all the other microcars. This is less sophisticated than a 1960's VW Beetle. We've all moved forward.......... And if you have a 1967 Mercedes you won't meet the 54mpg no matter whether it's gas or diesel. Ford of England website says the Focus gets between 44.1 and 67.3 combined using either the 1.0 gas or 1.6 turbodiesel. Probably using Imperial gallons. Not quite the easy 80mpg. For the VW Polo. Highest I could find from tests. Best 51.5, avg 49.6 from a 3 cylinder diesel. We all think europe is so much better. Higher gas prices subsidize mass transit, which I'm for, by the way. Driving in Switzerland or Austria is extremely restricted, and lower speed limits than U.S. which would also help explain higher mpg. Load down a small car with a few people and cargo, and watch the mpg plummet.
Think about pollution regulations for a second? How could it be better to get low mpg in order to meet pollution requirements? Obviously pollution is not being fairly measured. It is insane to measure parts per million, when in reality a car puts out half the amount of pollution total. If they changes the DEQ measurements to capture a volume of exhaust over a period of time and measure the total, then high mpg would easily negate things like heavy air pumps that don't really help at all.
England has a Ford Focus and Germany has the VW Polo that get over 80 mpg, at higher than highway speeds, safely and reliably. There are dozens of others as well.
Safety equipment for the Tata Nano to be brought to the US, is actually just padding, and does not weigh much of anything, nor does it change mileage.
It is nice to pretend the US has safer cars, but I will take a 1967 Mercedes over a modern US car in an accident, any day. Putting an explosive airbag in your face makes a car more dangerous in an accident, not safer.
>Rest of the world gettng 80 mpg >Rigby5 9/12/2012 12:56:33 PM
>I was buying 4 cylinder cars in the 1960s that got 30-40 mpg, such as VW, Fiat, Renault, >Mercedes, Corvair, Pontiac Tempest, Nash Metropolitan, etc.
>Asian and European cars easily get 80 mpg, mostly with turbo charged diesels.
>Lets not pretend that 54 mpg is hard.
>We all know it isn't.
I think back in the 60's, and in the rest of the world, there were/are other a) safety requirements, and b) emmission standards, that effect mpg. So if we are to compare US mpg with these we need to compare other constraints put on american cars. ARe we going to relax these to get to 54 mpg? I have a '89 Dodge Colt Stationwagon with a 1.5l engine that get 30+ mpg in town, and its not a dog, it has some pep, but I think its very light. (I also note this engine is smaller than what is in the GM Volt!
Totally false. I HAVE owned a diesel Rabbit, and it was one of the safest and most comfortable cars on the road. It also looked nice, has great carrying capability, and was easy to park. It was weak, but sufficient. And with turbo charging, diesels are much better than gasoline cars for power, mileage, ease of maintenance, and longevity.
Good thinking for cars, but a 4.5L couldn't give the same performance when towing and hauling that the bigger engine does. Also, truck buyers are much more performance driven than the average car buyer.
Any advancements for trucks will likely have to come from optimizing the engine. Hybrid technology just doesn't add that much in the current state of the art.
I have to agree with you on this one. Every time the auto industry has been required to comply with a regulation, they whine that it's too expensive, nobody will want to buy the cars, the auto industry will be driven out of existence, cars will actually be LESS safe (or efficient or whatever). Safety glass, seat belts, pollution controls, shoulder belts, air bags, CAFE standards, crash test standards, pedestrian safety standards and many others; all have been decried as the death of the auto industry, the end of "affordable" or "desirable" cars, and every one of these goals has been achieved ahead of schedule at much lower cost that originally stated, with much less disruption to the industry, and without destroying sales of cars. And all of these standards have improved safety, fuel economy and driveability.
We've got to at least try to get there, even if we don't quite make it. Some bright boy (or girl) will figure this out and make a fortune.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
