I'm not sure about the math on this one... A bit of 'could you double check that math' is going on...
"Dhar says he could replace the 16-kWh lithium-ion battery in the Chevy Volt with a 3.5-kWh lead-acid battery and a 9-kWh lithium-ion pack. Doing so, he believes EPS could cut the battery pack cost of a Chevy Volt from approximately $12,800 to under $6,000."
So... 16kwh Li = $12,800 ($800/kwh-Li)
but... 9kwh Li + 3.5kwh Lead = $6,000? ($555/kwh-Li assuming $1000 for the lead/integration)
The loss of $49K per Volt was poor analysis. That number is assuming all the cost are recovered in the first year, not spread out over production life.
Naperlou,, That's just what I've been saying for yrs. Start with reliable tech and then do what you are paid for, design a car around it that makes it work as a system.
Lead is a great battery, very cost effective when designed right. I'm about to go pick up some construction supplies in my lead powered Harley size EV trike pulling it's 14' trailer.
Fact is a 500lb composite 2 seat commuter/town car EV with 500lbs of quality lead deep cycle batteries can go 80mph and 100 mile range, though not at the same time, and be built for under $12k with a nice profit. But as these are not profitable, no rust, few parts to go bad, after the sale big auto and especially big oil hates them.
That said strings of 30 12vdc lead batteries in the article needs a BMS to keep them alive so if a li hybrid battery system now you need 2 complete battery BMS, etc plus cordinating electronics, it's better to replace the li battery with a small ICE like the Toyota X-1 though with lead, to give unlimited range.
Better is fewer cells, lower voltage like 100-120vdc of lead. Since a lightweight, very aero EV needs little power to go a mile one needs a much smaller battery pack to get decent range. My earlier EV sportwagon got 10 miles/kwhr or better. My Trike gets 20miles/kwhr shows what can be done.
Using forklift EV drive tech gives excellent performance at a reasonable cost.
EV's are selling. the Volt is not an EV but a hybrid, if they were not overweight, overteched, overpriced, they would sell.
As for battery life, lead with a good BMS will last 5-7 yrs then only needs to be rebuilt as almost 100% of them are recycled into new batteries. So one could just pay a reforming charge as no new materials are needed and have a new pack.
It's amazing how so many throw up such misinformation about how EV's can't work or limited when there are simple solutions.
So keep paying at the pump as it rises to $10'gal in 5 yrs. It only costs me a couple $/month for my transport fuel and I don't support oil dictators or terrorists it pays for.
Good points, Contrarian. The drop off in sales of EVs, and the reluctance of hybrid owners to buy a second hybrid shows this market is presently very limited. It seems to me these vehicles are mostly for those who are interested in preserving the environment and have a few extra bucks to overspend on a second car. The price of gas isn't going to go high enough to justify the investment in an expensive gas saver. Hybrids and EVs will likely remain a small specialty market until technical breakthroughs change the present scenario.
This was a great article. It is exactly the type of thinking thats needed to draw hybrids away from the fringes and make them a reality for a broader range of vehicles. It's refreshing to see that someone has finally decided to drop the costly idealism associated with so many of these alternative technologies and is moving forward with technology that makes more sense economically.
Lead acid batteries have been around more than a century and even in high volume applications like SLI they still haven't been supplanted by alternative chemistries. These high performance batteries just don't scale and in the case of Lithium vs oil, all you're doing is trading the source of natural resources from one non-US friendly country to another.
Most people don't need 0-60mph in 4 seconds and 300 miles on a single charge, especially if the vehicle ends up costing more than their home. Build an EV or hybrid that competes with ICE in terms of cost per mile and TCO and you'll have a winner, irrespective of the source of electrons. Most people don't care if their cars run on gasoline, electric or the squeezings from baby seals - they just want a car that gets them from A to B in the most affordable way. EV's or any other alternative fuel will not succeed unless it's artificially mandated through law or solves an economic problem.
Ford is probably on the right track with their multi-drivetrain Focus. Remains to be seen if they can get the price point where it needs to be.
As energy efficiency becomes more and more a concern for makers of electronics devices, researchers are coming up with new ways to harvest energy from sound vibration, footsteps, and even electromagnetic fields in the air.
The government wants to study your brain, and DARPA wants to use similar information to give robots true autonomy beyond any artificial intelligence developed to date. Sound like science fiction? It's not.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
1 
