Sounds like this is another move toward greater gas mileage as well as a better clamp. If you can get V8 performance out of a V6, we're moving in the right direction.
Rob, that's just what I have been saying! It is interesting that in Formula 1 racing the turbocharged engines are limited to 1.5L as oppossed to the naturally aspirated engines at 3.0L. Just an aside, these engines put out over 700HP. We can get the horsepower we need to drive our vehicles with less fuel, but it will take lots of engineering to make them as reliable as the current engines. This is just one good example of an engineering "detail" that is critical to success.
I agree Naperlou. With all of the attention on the innovation going into EVs and hybrids, I think some of the innovation on traditional gas engines is getting overlooked. In the long run, improved internal combustion engines may save more gas than electric vehicles.
I agree, Rob. This is going to be an important part of getting the CAFE up to 54.5 because it enables automakers to put smaller engines in their cars and trucks.
Way back (late 1960's) when I worked summers as a part-time janitor for a school district, they had cleaning supplies deliverd in fibre drums (sweeping compound, etc). The lids on these drums were retained with exactly the same form device with the band in a U or V form to lock the lid to the top rim of the drum and with either a draw screw or over-center-snap link to draw thins tight.
OK this is a high temp alloy as needed by the application, but this is not new.
I believe you missed the point they are trying to make. I would blame the author for not showing an illustration of the thread form. It is not the V-Band Clamp that they are talking about as new. It is the thread form that they refer to as Spiralock. By the way, this thread form is not new either. Someone just seem to be promoting it for a new found application.
Spiralok has been around for a long time, but engineering folks need to be reminded or newly presented with this product's capability, every so often. I still have a Spirolok demonstration assembly on my desk. It reminds me of this potential solution, every time I glance at it. Many coworkers have picked it up and examined it, over the years.
I followed the Spiralock link to it's Technology page. The thread shape is interesting. But I agree, at best it is just a mating of two existing technologies.
The part in the photo looked very familiar. I went to my "secondary" desk behind me and picked up the part. The photo looks identical except mine has a hole for safety wire. The inner part is made up of two 180 degree parts, each with a "thread" cut on the inside and the clamp holds both parts together. It is used on a Gulfstream G1 turboprop 40kw auxillary power unit. The plane itself was built in 1958! This mechanism was designed so one mechanic could hold the heavy generator in place while another attached the "nut" to remove the loading. The strap holds it all in place and is safety wired to prevent it from coming apart unexpectedly in the air, always bad juju! It was no doubt an expensive part. It appears that auto manufacturers have found a cheaper was to fabricate them, but it is most certainly not new.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
