Your printer is an international product, and my printers are quite happy with any size paper.
"Saying the US and Britain are the only 2 countries using this backward system is perhaps a bit elitist." - I don't understand that, as a scientist I have no doubt that non-metric is backward.
In fact a little research shows that Burma/Myanmar and Liberia are also non-metric. I have litle doubt you will feel superior to those countries.
The cost of maintaining dual standards is enormous:
from http://www.metricationmatters.com/docs/CostOfNonMetrication.pdf
When the Confederation of British Industry (CBI) surveyed its members about metrication in 1980 — after 15 years of British metrication — they found that
"... the extra cost of continuing to work in dual systems of measuring was around £5 000 million every year."
This cost must be a huge drag on competitiveness. Even if the USA does not like metrication internally, many foreign markets will demand metric products, and manufacturers have a choice of dual standards of losing buiness.
To an individual, an additional or new machine is an unwelcome cost, but if everyone is replacing old machines over a period, the simplification of uniform standards must be a big benefit. There is nothing to stop a lathe from being set to 25.4mm to cut 1" for old legacy compatibility.
Contrary to popular belief Canada is not realy metric, it is only officially metric. I have lived here all of my 53 years and it is metric for visitors as the speed limit and gas and milk(not butter 454grams =1 lb) are all metric but materials to construct any thing are all in inch sizes, so when you design something if you want to not wait months for the material to arrive, you must use inch sizes. Going all metric would help as all of our new engineers have to learn ft/lb, psi....
The idea of metric conversion is much easier than the application. Try and purchase Metric paper for your printer, then try and re-adjust your printer to use it. Architectural building drawings are still mostly in Feet and Inches. When was the last time you found a metric drill index? They are all SAE with the metric value in parenthesis. All this is after almost 50 years of trying to change. There are not enough market forces to demand a change to metric and depending on the government to oversee this dooms it to failure before it even starts. Saying the US and Britain are the only 2 countries using this backward system is perhaps a bit elitist. I have no hard data, but I think these 2 backward countries do contribute a significant percentage of the worlds industrial output. Change is happening slowly. Maybe in another hundred years we'll all be metric but I wouldn't count on it.
I have been a machinist and have a few machinr tolls at home. I participate in several machinist forums and have seen this discussion come and go over several years. As long as one understands the system one is working ai and how it relates to the other system there is little, if any, problem. Sure, The Brits and the Americans still work with inches and the rest of the world works with meters. We can both make parts that are completely interchangeable with no extra effort. The arguments generally come down to - your system is wrong because it isn't my system.
Consuder the cost of retooling. If I was active in a machine shop my measuring tools alone would come to approximately $3000.00 to replace. Quite a hit to the individual craftsmans wallet and they aren't paid all that great anymore.... And then the companies that have thousands of dollars worth of tooling that would have to be replaced. And for what? so we could say we made it to 25.40MM instead of 1.000"?
The anecdotes that are used to justify metricization are more examples of poor communication and poor practice. The satelite and mars probe problems were more likely caused by a rushed production and testing program and revealled a need for better quality control. Rushed work in metric can still come out as crap. and chromed crap in metric or english is still crap.
As far as I know, the UK and the USA are the only two backward countries to remain non-metric in everyday life. All science and most engineering is metric already. The funny thing is, the UK and USA cannot even agree on units - US gallon is 3.8 litres and the UK gallon is 4.55!
The US claims "a pint's a pound the world around" but that is only true in the USA, in the UK a pint is 20 ounces. Talk about parochial!
TJ, the units are not the only potential pitfall. When I first started programming satellites, we were given the lecture about telemetry. Specifically, we were told to pay attention to the sign of the numbers and the endian-ness of the numbers. Evidentially there was a satellite where the mistake was made and the programmer shot the craft into deep space instead of putting it into a stable orbit.
Jon, it's very important to use international metrics/standards in business, especially with other countries, otherwise conversion from one unit to other is a problem. For domestic purposes, if we are using our own metrics and standards, nothing going to be happen because both the seller and buyer are following the same metrics.
Naperlou, events proved NASA to be correct. The Mars Climate Orbiter was lost because the prime contractor used metric units but the ground software used imperial for thrust calculations.
The only way is to do it by government edict, in the way South Africa and Rhodesia did in the 70's. After such-and-such a date everything will be made in metric. Imperial measurements will no longer be taught in school. Old equipment can be maintained but all new equipment will be metric. S.Africa went further and banned the importation of imperial measuring equipment.
I have done a couple of science classes here in the US and it always amazes me how 'conversions' are taught and seen as a very abstract concept. One prof got all annoyed when I pointed out that mixing units(sq metres/acre) was not standard.
However, it takes years to clean out 'imperial'. In the 80's a fellow apprentice fitter- and-turner was happy because he had been given a set of imperial micrometers. If you make imperial size parts make them in imperial - conversions(either way) are never the same.
Here in the US we brought in some European equipment. We had to fabricate mold plates locally. Our machinists insisted on converting to inches(on CNC machines). 80 plates later, and all 1/16" too short I was free to say 'I told you so'.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
