I don't remember speaking of efficiency. But electric drive efficiency is pretty high; there's not much margin between today's numbers and 100%. The area for improvement is in batteries; the problem there is that it's not clear how.
As for control, what's the problem? For starters, each wheel wants to have torque delivered to it. Then you can look at traction control (anti-skid) which of course is inherently a per-wheel activity; conventional cars have to approximate that because they have centralized drive, and per-wheel drive makes it much easier.
If you're not doing traction control, the whole thing is trivial. Consider that electric trains (the motor car style) have had per-wheel drive for close to a century.
Pkoning, am first time hearing about vehicle with motor on wheels and I don’t know how centralized control is possible for all independent motors. Any idea? Why you are telling that efficiency is not going to change-any particular reason.
NOT a novel design approach...not even close!!! About 115 - 128 years off.
The first electric car hub motor was patented in 1884. In 1897 Ferdinand Porsche had an electric wheel hub motor "race car" that had a top speed over 65mph! There were over 300 of these fast electrics built and they were all sold to wealthy customers. The only novel approach I can see with this new electric car is that it is using a new type of plastic for the bobbin.
Below are some pretty interesting info:
In 1914 a Detroit Electric went 241 miles on a single charge setting a new record!
In the 1900's there were over 300 electric car companies with more than 30,000 electric cars on the road.
The first powered taxis in New York were all electric,.
The fastest race cars in the late 1890's were electric.
Unfortunately when it comes to putting things together on the shop floor or getting things from an outsourced location a whole lot of things can go wrong. Military aircraft and smaller aircraft built around composites are entirely different from commercial aircraft carrying a large number of passengers. Boeing's Dreamliner had its share of manufacturing problems significantly related to composite glitches and although most of them were dispositioned by the Liaison Engineers there are (inevitably) those which are still lurking in the aircraft...that's also a fact. Aluminum structure problems are generally self evident....composite problems are subtle but still there. My associates and I like composites....in their place...but there are things that do go wrong which don't cause grief in aluminum structures....just ask any stressman.
In Quebec and Ontario they are regarded as power assisted bicycles limited to a maximum speed of 20mph and must have the pedals attached. The rider must wear a DOT approved helmet but there is no requirement for a vehicle licence, driver's licence or insurance. Since they are regarded as bicycles they can be driven anywhere a bicycle can be driven. Recharging a 48VDC system takes 11 cents of hydro and depending on use may take place every third day. They are ideal for shopping and general tootling around town.
Interesting, ScotCan. Are these vehicles legal on the road? On bike paths? I would think these would be ruled by state regulations, each of which would be different. I'll bet there is very little energy consumption with these vehicles.
Carbon composites have been used in aircraft for decades, beginning with the military, and anything going into the construction of commercial aircraft has very strict specifications and requirements, including extensive testing on the ground and in the air. That's all fact. So is the conductivity of metals such as copper and aluminum. Carbon composites can be, and are being, designed with specific electrical properties to handle lightning strikes. Clearly, whether conductivity is a problem or not depends on how the materials and components are designed.
Some cars are more reliable than others, but even the vehicles at the bottom of this year’s Consumer Reports reliability survey are vastly better than those of 20 years ago in the key areas of powertrain and hardware, experts said this week.
Many of the materials in this slideshow are resins or elastomers, plus reinforced materials, styrenics, and PLA masterbatches. Applications range from automotive and aerospace to industrial, consumer electronics and wearables, consumer goods, medical and healthcare, as well as sporting goods, and materials for protecting food and beverages.
While many larger companies are still reluctant to rely on wireless networks to transmit important information in industrial settings, there is an increasing acceptance rate of the newer, more robust wireless options that are now available.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.