HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Page 1/2  >  >>
Beth Stackpole
User Rank
Blogger
Re: Inspiring
Beth Stackpole   8/23/2012 8:13:27 AM
NO RATINGS
@kellerbl: It sounds like there will be some great opportunities for your grandson and isn't he lucky to have a granddad that is so up on the technology to pose some suggestions. The team that developed the WREX is Dr. Tariq Rahman and designer Whitney Sample--both from the Nemours/Alfred I. duPont Hospital for Children in Wilimington, Del. (Don't know where your grandson is)

Here's a link to Dr. Rahman's information.

 

Greg M. Jung
User Rank
Platinum
Re: Printing repacement parts...
Greg M. Jung   8/22/2012 9:07:37 PM
NO RATINGS
I imagine as a younger patient grows, the design could also be quickly scaled up little by little and printed again (to help save prosthetics fitting time too).

Rob Spiegel
User Rank
Blogger
Re: Printing repacement parts...
Rob Spiegel   8/22/2012 12:06:21 PM
NO RATINGS
What I'm wondering, Beth, is whether the device is external support for her arms or whether it is a joint replacement/support that has been inserted within her arms.

kellerbl
User Rank
Silver
Inspiring
kellerbl   8/22/2012 10:00:49 AM
NO RATINGS
I can see that it would be great to work in this field. I have a 4 year old grandson born without one arm - not even a shoulder. I have wondered if it would be possible to fit him with a wrap-around vest that a prosthetic arm could be attached to. The hand on his one arm has only a thumb and two stubby half fingers. This handicap is apparently due to his arm and hand being pinched off during development by the amniotic membrane. He is a very happy child who doesn't yet recognize he is so different from others and he naturally uses his feet when one hand can't complete a task. He may never need a prosthetic to get through life, but it would be something worth checking into.

Beth Stackpole
User Rank
Blogger
Re: Printing repacement parts...
Beth Stackpole   8/22/2012 7:56:25 AM
NO RATINGS
With prices on 3D printers coming down and with materials and other related technologies vastly improving, I do think capabilities like these will become easier and more accessible to mainstream medical practices, aiding in their adoption.

Beth Stackpole
User Rank
Blogger
Re: Printing repacement parts...
Beth Stackpole   8/22/2012 7:53:43 AM
NO RATINGS
@Greg: That's actually a point I didn't spend time on in the post, but a real lifesaver for Emma's parents. There is obviously wear and tear on the device, particularly as Emma gains in mobility. With the 3D printing approach, her parents can simply contact the research/medical team and explain what part is broken (take a picture if need be) and a replacement can be easily and cheaply produced. Minimal downtime, which is a great thing for Emma.

Beth Stackpole
User Rank
Blogger
Re: Printing repacement parts...
Beth Stackpole   8/22/2012 7:50:46 AM
NO RATINGS
Rob: Magic arms is actually just a pet name she gave to the prosthetic device that helps her now have control over her arms to do everyday things like play and feed herself. It is more of a term of endearment to show her enthusiasm for new mobility.

Scott Orlosky
User Rank
Platinum
Re: Printing repacement parts...
Scott Orlosky   8/21/2012 11:15:38 PM
NO RATINGS
It's great to see these types of advances taking place.  Just in the same way that high performance cars eventually see their developments embodied in the consumer versions - I hope that these techniques eventually become available to the average consumer. What a boon to veterans, the disabled and the aging.

Charles Murray
User Rank
Blogger
Re: Printing repacement parts...
Charles Murray   8/21/2012 9:31:10 PM
NO RATINGS
What a wonderful story. If Oscar Pistorius' performance in the Olympics taught us anything, it's that prosthetic limbs needn't be a handicap. I really do believe that technology will eliminate all disabilities by the end of this century.

Greg M. Jung
User Rank
Platinum
Re: Printing repacement parts...
Greg M. Jung   8/21/2012 4:38:16 PM
NO RATINGS
Yes, I also agree.  An inspiring story about Emma that really drives home the point on how technology breakthroughs can have such a positive impact on people's lives. Since the cost of 3D printing has come down so much, I imagine that new arms could also be printed again should the current ones wear out or become damaged.

Page 1/2  >  >>


Partner Zone
Latest Analysis
It's been two years since the Mac Mini's last appearance on iFixit's teardown table, but a newly revised version joins Apple's lineup this week.
More often than not, with the purchase of a sports car comes the sacrifice of any sort of utility. In other words, you can forget about a large trunk, extra seats for the kids, and more importantly driving in snowy (or inclement) weather. But what if there was a vehicle that offered the best of both worlds; great handling and practicality?
Kevin Gautier of Formlabs describes the making of a carbon fiber mold for an intake manifold, using a $3,300 3D printer, during Medical Design & Manufacturing Midwest.
Science fiction author Isaac Asimov may have the best rules for effective brainstorming and creativity. His never-before-published essay, "On Creativity," recently made it to the Web pages of MIT Technology Review.
Much has been made over the potentially dangerous flammability of lithium-ion batteries after major companies like Boeing, Sony, and Tesla have grappled with well-publicized battery fires. Researchers at Stanford University may have come up with a solution to this problem with a smart sensor for lithium-ion batteries that provides a warning if the battery is about to overheat or catch fire.
More:Blogs|News
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 20 - 24, How to Design & Build an Embedded Web Server: An Embedded TCP/IP Tutorial
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: 10/28-10/30 11:00 AM
Sponsored by Stratasys
Next Class: 10/28-10/30 2:00 PM
Sponsored by Gates Corporation
Next Class: 11/11-11/13 2:00 PM
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service