There are a few polymer-eating bacteria, although so far I don't believe any have been corralled to harvest plastic from the oceans. I'd love to find out differently. Anyone know?
@sbkenn: On the subject of plastic contamination in the oceans, Donovan Hohn's book Moby Duck is a fascinating read. He tried to track the journey of 28,800 bath toys that fell off a container ship. I highly recommend it.
@Beth, it is said that a teaspoonfull of sediment, from any bit of sea floor on the planet, will contain visible pieces of plastic. A shocking reflection of our habits IMO.
I know that there are bacteria that consume iron(very slowly), and oil, but not sure about polymers.
I like your plug and play idea, Ralphy Boy. And if that fails, I'd opt for the duct tape. There are very few things duct tape won't fix -- except a leak in a swamp cooler hose, as I found out recently.
I didn't get to see the video yet (at work), but I am wondering how easy or hard it is for parts to be scavenged from one sat and then applied to another.
Even on sats of the same type there could be hardware and alignment issues. We make small changes to print packs all the time. I'd hate to see a bot going from one out of service sat to another searching for a hole/pin alignment match. Or filing out a hole to get a fit... ; )
Also, a lot of things might be potted in place, or otherwise hard to remove. Perhaps a tile knife, some outer space approved duct-tape, and a spool of bailing wire would be a handy addition to the tool box.
On the other hand, if it hasn't already happened... a plug and play, snap in place assembly line-one size fits all design regimen in the future could insure a high rate of retro-booting.
We made 100+ battery packs for a sat network some years back. They were all identical. If some of those are bricks, and other sats have been shut down for other reasons but the batteries might still be good... that might be a worthwhile swap depending on how the 2kg packs were installed.
bob, thanks for quoting that info from NASA's site on space junk. It's amazing how many small particles there are, but scary how many large ones weighing more than 200 lbs are flying around.
@Shane: Love to hear more about robots cleaning up the junk on the ocean floor as well. My guess is there's probably more stuff to clean up in the deep waters than out in space.
Cute exercise in Gallilean relativity, but why did you add all those velocities as scalar quantities? Unless thye are all in the same direction, you need to add them vectorially. Still, what's the point? For the space junk problem what counts is the velocity of a piece ralative to a satellite with which it might collide.
Andrew Morris designed a circuit that could detect a stroke victim's groan and convert the sound into a signal so caregivers would know when help was needed.
New disc magnet motors fit into the design trend of stepping up to closed loop performance while maintaining the cost advantage of stepper motor technology.
At the Design News webinar on June 27, learn all about aluminum extrusion: designing the right shape so it costs the least, is simplest to manufacture, and best fits the application's structural requirements.
On April 21, NASA launched a novel project, putting into orbit three satellites that employ an off-the-shelf commercial smartphone as the control system.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
