HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 2/2
KCB
User Rank
Iron
Re: They don't want a better design...
KCB   8/15/2012 12:44:45 PM
NO RATINGS
kfq2d...

I think they call that "designed obsolescence."  On your

other comment regarding "design engineers," I've often

said, especially in regards to automobile engineers, that

they should be required to spend a year working in an

auto repair facility before they're allowed to work in a

designing capacity.  Nothing like a little hands-on, grease-

under-your-fingernails experience to let you know how the

real world works.

KCB
User Rank
Iron
Re: Not sure
KCB   8/15/2012 12:35:29 PM
NO RATINGS
naperlou...

It hasn't been very long that the clip's been in there.  I will be checking it

regularly however.  I would imagine that it will rust also.  I recently put

this same problem on a "Tractor" website and one responder said he's

been using the mulch cover without the clips to hold it in place.  He says

the metal deflector does a fine job of holding it in place.  I'm going to try

that and see what happens, because I can see that the same issue you

brought up will start to occur with the front clip as well.

kf2qd
User Rank
Platinum
They don't want a better design...
kf2qd   8/15/2012 11:59:46 AM
NO RATINGS
Many of these products really seem to be designed so they will fail. And then you won't be able to get some part because they design was changed. They see it as a way to generate sales!

I have a couple of small machine tools at home and ther have been a number of time where I have made some simple part because the manufactirers part is either unavailable or way too expensive. If I can make it in 15 minutes why does it have to cost half te cost of the whole machine new? But then, most folks haven't the basic skills to open something up and repair it. Perhaps that is what we ought to be teaching in school nowadays. Then we might get better engineers and factory workers making better products.

Sorry to rip on the engineers, but they are involved in many of these "Made by Monkeys" complaints. How many of the engineers would be lost if handed a mechanics toolbox or a set of micrometers?

naperlou
User Rank
Blogger
Not sure
naperlou   8/15/2012 9:00:01 AM
NO RATINGS
Ken, I have a similar mower (the auto trans version) and the same mulching cover, which we use.  I will have to check (I'm not home now), but I have not noticed any rusting or other problem.  If I do, I will comment later. 

Have you noticed rusting in the hole through whcih the clip goes?  This would be another area of contact?

<<  <  Page 2/2


Partner Zone
Latest Analysis
Bigger than an iPhone 6 Plus, but smaller than an iPad Air 2. What am I? If you answered iPad Mini 3, you are correct.
Here are 10 robots that are designed to work effectively and safely with humans.
The data breaches at Target, Home Depot, and elsewhere have inadvertently highlighted a separate and unexpected problem: bad user interface design.
What if you could recharge your mobile device using the movements you make all day? That’s the promise of Ampy, a new device by a Chicago-based startup of the same name.
Peter Riendeau of Melexis shows how a time-of-flight sensor can be used for gesture recognition in a vehicle.
More:Blogs|News
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Nov 3 - 7, Engineering Principles behind Advanced User Interface Technologies
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: 10/30 11:00 AM
Sponsored by Stratasys
Next Class: 10/30 2:00 PM
Sponsored by Gates Corporation
Next Class: 11/11-11/13 2:00 PM
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service