Chuck, I didn't see any data on actual energy produced, only efficiency ratings. Kevin did some rough back-of-envelope calculations in his comment, and came up with an estimate of 1.2 KWH of power per square meter of window per month (given certain reasonable assumptions).
Jack, the material is slightly less than 70% transparent, letting in less light than 100% transparent materials. That may account for what you see in the photo, and it would presumably block some heat and possibly some UV.
From the photo (which might be photoshopped) it appears that glass has some "light blocking" properies as well. I wondering if the use of this technology would eliminate or reduct the need for tinting which will help reduce the heat and UV energy like what is currently in autos or even new residential windows.
Mydesign, we have somewhat similar programs here. The programs still have an initial up-front cost that can be beyond the resources of many people. Other programs with practically zero up-front costs leave the homeowner a renter, or lessor, of the system, not its owner. At least in my state, the offers I've seen from various solar panel installation companies seem to be aimed primarily at people who use electricity for heat. Those of us in rural areas use other sources for heat, and many, like me, are under a forest canopy so there's not a lot of sun.
Ann, in our country both federal and state governments are offering 60% (30+30) discount for domestic house hold consumers, how are willing to invest in solar energy as a part of promoting ecco friendly energy sources. So the end customers have to bear only 40% of the cost and can have green energy with minimal investment. Am not sure about other countries, but if they are also able to follow similar policies, then investmental cost may not be a big issue.
Kevin, I agree that much of the potential success of deploying a new technology like these solar windows will depend on the simple economics. There is a certain portion of the population who would invest without a positive economic calculation -- those who buy EVs -- but in most cases, the technology will have to pay for itself.
Rob and Beth, I think that's a good point: this kind of technology may be best applied to large buildings with a much higher ratio of glass surface area to total exterior surface area.
It's true - we are very "spoiled" by the concentrated energy delivery of today's electricity and natural gas. Renewable energy sources are by nature more diffuse and present a great challenge in concentrating / converting / storing it. I think that energy-efficient designs of the future will tap into multiple energy-saving and energy-production sources (passive and active), to acheive an overall energy footprint that makes a difference in our homes.
For example, in Southern California we often pay to have our south-facing windows covered in reflective solar film to keep the home cooler - why not pay a bit more and get the added benefit of a little power? The key to practicality, of course, will be low enough cost.
I ran a thumbnail "back of envelope" calculation on the economics: A 1 square meter window can get ~1Kwatt of solar flux in optimum conditions. Derate for geometry of orientation, let's say 50%. Let's optimistically use 10 hours of sun for 30 days, and the 4% efficiency of the conversion. That gives 1.2 KWH of power per square meter of window per month. At a rate of 14 cents per KWH (my local total rate), that gives a payback of 17 cents per month, or a couple bucks per year (per window)...and that is assuming all sunny days. Sadly, I don't think this is going to produce a reasonable break-even timeframe, esp. if you include the true time-value of money in the calculation.
So...my intuitive take-away is that for solar energy to become economically viable - one needs to push as hard as possible on reducing cost and increasing efficiency. Even then, it's a challenge. To give up a huge amount of efficiency for the novelty of using windows (vs. say on your roof) for solar power does not seem to make economic sense. Note that my opinion shifted over the course of writing this comment, after I ran the calculations!
Ann, my point is that at least for me, the things that I use that use electric power need a good bit more than small amounts. Even my computer to participate in this discussion and answe all of my daily emails needs quite a few watts. And collecting the power from a dozen windows effectively is not trivial, particularly if one complies with all of the codes, which have no regard concerning the cost of implementation. Of course in a sunny cliamte and in a building designed for maximum efficiency, things could be different. But I don't live in that part of the world.
As for the smart grid, what the main benefit would be is the quick isolation and shedding, of sections that are in a failure mode. Dumping overloaded sections quickly in order to avoid massive failures is the only way to avoid repeating the massive failures of the past. Adding additional capacity will only increase the amount of power sold, since unused capacity provides no return on investment. BUt an effective smart grid, coupled with small enough sections, will be able to shed overloads quickly, avoiding the dreaded ripple effect that caused the past power outages.
Of course critics will complain that disconnecting overloads is a lot like rationing, which it may indeed be a form of rationing. But sometimes rationing does need to happen.
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 4
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
