HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Page 1/2  >  >>
naperlou
User Rank
Blogger
Use the software
naperlou   8/14/2012 8:50:32 AM
NO RATINGS
CAD and CAE tools often provide analysis of ESD and other effects.  This is very much like security in software.  Frankly, when design a program, at any level, the main concern is not security, or any number of other -ilities, but the funtionality of the program.  Design tools have been used for a long time to ensure that the software meets these requirements.  Hardware design has to take this into account as well.

tekochip
User Rank
Platinum
Not an Afterthought
tekochip   8/14/2012 9:19:47 AM
NO RATINGS
It typically isn't too complicated to make a device immune static discharge and surges, but it should certainly not be an afterthought.  Something as simple as adding a little series resistance to keyboard lines may be all it takes to keep from turning your silicon back into sand.  It's worth investing in, or renting a static discharge (simulator) gun.
 
As a side note, I was performing static discharge tests on a device with a membrane switch panel.  The device passed several tests, I turned off the gun and the reached for the device to turn it off.  I was greeted by a very hearty jolt, as the front panel was holding a healthy charge and using the switch panel as a capacitor.


richnass
User Rank
Blogger
Re: Not an Afterthought
richnass   8/14/2012 12:17:09 PM
NO RATINGS
It's funny what people think about as an afterthought. Earlier in the mobile era, people said it was always the battery that was an afterthought. Hence, we had more OEM battery shapes and sizes than the battery OEMs would care to remember. Then it was the wireless technology, which designers often thought of (for good reason) as being a black box that they could simply drop into their design. Now it's the circuit protection. What's next?

Jon Titus
User Rank
Blogger
Keep EMC, RFI, and EMI in Mind, Too.
Jon Titus   8/14/2012 7:18:58 PM
NO RATINGS
Designs must also take into account suppression of electromagnetic and radio-frequency interference, and compatibility with other devices. Lack of attention to these effects can cause an expensive failure when a product undergoes compliance testing.

I recall an engineer telling me a device would not pass an emissions test because someone had cut ventillation slots in a metal case for the device. Thise openings served as perfect slot antennas for signals generated inside the box. If you don't think about this "stuff" you can get into trouble rather quickly.

mrdon
User Rank
Gold
Re: Not an Afterthought
mrdon   8/15/2012 5:15:47 PM
NO RATINGS
In addition to circuit protection, power supplies are an afterthought as well. Being an engineer, I'm guilty of focusing on the key subcircuits of the products I've design and realized they needed clean efficient power to operate. To eliminate this afterthought mindset, I'll include in my system architecture design a sub-block for power supplies, interconnectors, and circuit protection devices.

Avnet Electronics is hosting its annual virtual Power Forum conference. Circuit Protection, power supplies, interconnectors,  batteries, and electromechanical devices lectures will be presented in this virtual event. For additional information the weblink is shown below.

http://www.em.avnet.com/en-us/design/trainingandevents/Pages/Avnet-Power-Forum-2012.aspx 

Charles Murray
User Rank
Blogger
Re: Not an Afterthought
Charles Murray   8/15/2012 7:21:59 PM
NO RATINGS
I remember hearing the same things about batteries, Rich. I suppose most suppliers would just like to see their technology get promoted to a higher spot on the designer's list.

Nancy Golden
User Rank
Platinum
Do Not Use As A Cattle Prod
Nancy Golden   8/16/2012 12:05:28 PM
NO RATINGS
Reading this article brought back a lot of memories. At one place I worked we had an automated ESD tester for our ram chips - you could seat the part in the fixture and program in the voltages and it would both zap and test the part. In product engineering at another company we would do ESD testing on our discrete hall effects with a handheld tester. You would adjust the voltage and then place the tip on the lead and give it a zap - then test it afterwards. While it is important to have protection circuitry - hopefully the problem is also being addressed at the discrete level like we were doing. We always cracked up laughing at our hand held ESD "Zapper" - the instructions specifically directed the user "Do Not Use As A Cattle Prod." 

bobjengr
User Rank
Platinum
CIRCUIT PROTECTION
bobjengr   8/18/2012 9:47:08 PM
NO RATINGS
Charles, this is an extremely important article.  When I was in the aerospace industry we would frequently visit Titan II silos to affect repairs.  As a member of AFLC, I worked on the thrust chamber and the turbopumps for that defense system.   Initiation of launch required the firing electrical "squibs".   This was accomplished with a 28 volt DC source.  With this low voltage, it would not be impossible to ignite the squibs with static discharges.  This has happened.  Due to this possibility, we were not allowed to bring or wear metal objects into certain levels of the silos.  No belt buckles, no wedding rings, no watches, no jewelry of any kind.  Even the eyelets in our shoes had to be taped or booties worn.  For some areas, special clothing was also a necessity.    I can certainly understand the need for proper circuit protection regarding electronic devices such as the ones you mentioned.  This will be an ongoing problem unless engineers and engineering managers address the possibilities.

 

tekochip
User Rank
Platinum
Re: CIRCUIT PROTECTION
tekochip   8/19/2012 9:56:46 AM
NO RATINGS
Static discharge has caused a few accidents with missiles.  in `84 there was a
fatal accident of a Pershing II that burned its 4 tons of propellant.  The motor
was being removed from the casing at the time of the accident and the discharge
ignited the motor from the inside.  The unfired igniter was recovered from the
scene.

Charles Murray
User Rank
Blogger
Re: CIRCUIT PROTECTION
Charles Murray   11/8/2012 6:59:14 PM
NO RATINGS
It truly is an important topic, bobjengr. I can't prove this, but I suspect circuit protection often gets overlooked because it never gets mentioned in school.

Page 1/2  >  >>


Partner Zone
Latest Analysis
Robots came into their own in the 1970s. Gone were the low-budget black-and-white B movies. Now robots roamed in full-color feature films with A-list actors.
The rear window on Ford's Lightweight Concept vehicle, based on the Fusion model, is made with a material combination devised by SABIC that saves 35% of the weight. The car's overall weight is 25% lighter than a standard production 2013 Fusion.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
There is still time to get in your gadgets for the Design News and Allied Electronics second annual Gadget Freak of the Year contest. The top three gadgeteers will be awarded a total of $10,000.
Major global metropolitan areas are implementing a vast number of technology, energy, transportation, and Internet projects to make the metropolis a friendlier, greener, safer, and more sustainable place to be.
More:Blogs|News
Design News Webinar Series
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
5/8/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 21 - 25, Design Products With Bluetooth Low Energy
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: August 12 - 14
Sponsored by igus
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service