Growing up, we had a TV from about 1970. In the 90's, we bought a VCR and after a few years, the TV required a good smack on top of it every time we used the VCR to alleviate a wavy screen. This worked for a few years until we got a new TV. I do not know what the smack did, but it felt good and it worked.
When I was growing up, we only had one TV as was typical in those days...a knob-tuning black and white 19-inch tube TV. From a very young age, I remember the standard family practice to get a better picture was to slap the top of the TV with an open hand...and it worked! (My Dad was an EE.) That old TV lasted forever though, so I was a teenager by the time we got a new-fangled color TV.
I haven't had to smack TV's since, except for when they broke after a few years. The old TV's seem to last much longer. I hope my new LCD HDTV's last a good few years, but I recently had to replace our first LCD TV at four years old.
The cost to repair electronics these days always seems to equal or exceed the cost of a new unit, so that means disposable consumer electronics.
What can I say - A few months back the power supply for my Dell laptop died. Like any good DIY fixer, I gave it a few small bumps and noticed the little green light flicker. Seeing some hope, I gave it a good forceful smack - and the thing came back to life. Its still going.
Sometime smacking can work for computers also. I know a couple people at work who have used the smacking technique - or perhaps more accurately described as the pick-it-up-and-slam-it-down technique. While this did not actually "fix" the computer, it successfully made it completely inoperable which meant that our computer tech friends had to finally quite fooling with the old PC and bring them a new one.
Nancy, I'm with you on that thought. Some of them get it and see the need for recycling, etc., but I think the whole concept of throwaway products is what they're used to, so it's a fish-in-water thing.
I agree Ann, and it is a shame. A telling point is that our teenage kids do not expect longevity in products - for them, throw-away is the norm and they are the next generation...
Nancy, I think all TVs were like that in the 50s and 60s, and so were stereo systems (but not the record player!). Like you, I've been surprised, and disappointed, to see just how short consumer electronics lifecycles have become. The throwaway society does not encourage good consumer product or machine design, among other things.
Use to call it percussive repair. Got to know where to pound, kick or slap though. Lately it seems that dislocated shoulders are using same technique;-).
gafisher - Smacking the salesperson's desk sounds pretty satisfying too...or the desk of the Sony rep who thought the problem was just an isolated incident...the problem is, these people are unreachable - the product was purchased at a Best Buy or some such store with an extended warranty added at the cash register.
My job at a local aerospace manufacturer included repooling mecury wetted relays. Just had to smack it on the bench in the right direction. Most times it worked. If not then it was time to replace one of the relays. Also repsitioning or resequencing the boards would help to identify just which one was bad. The other thing I did was vacuum the ATE to the tune of $35/ hr. What a job!
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
