Dave: I said the new guy finds problems that do not exist, not that he finds problems which have been overlooked. For example: on parts in a car frame the only dimensions that mean anything are the areas where a robot will weld and hole locations where something else will bolt into place. The rest is just transition from point to point and unless there is an interference with something else, it is in the wind and an design engineer probably signed off on the variance when the part was tooled. Many times material has been added to improve strength. The part may be on thousands of vehicles without a problem.
Then a new quality guy comes in and rejects a delivery because an absolutely meaningless dimension is out of spec. I know every drawing should be updated in a timely fashion, but that often does not happen in the real world. One engineer at a truck manufacturer told me it cost more to change the drawing than to grant an order-order deviance. So it was only after our customer was in a "line-down" situation that someone in engineering straightened the situation out by issuing a "permanent deviance authorization. (And before anyone gripes about American made autos, this was on a Toyota.)
I am not saying this is always the case, but most times when get rejections on a part which was tooled in the 60's and has been in contiuous reorder on a variety of new models, we find there is a new guy involved. But then again the new guys often keep us dinosaurs on our toes, so it is all good.
A few years ago I was a "new guy" in a research group, and I did find a serious problem. Of course, being aware of how departmental politics worked, I was careful in handling my discovery. What I did was ask my associate, the scientist that I was supporting, what the significance of the one parameter that we were measuring meant. At first his comment was that it really did not mean very much, but then two days later he asked about how certain I was that my measurements were correct. I described my procedure and he was satisfied with the accuracy. The following Monday I was asked to join a meeting where our manager explained that my associate had noticed a problem with some of our original assumptions, (made prior to my joining the group), and we needed to make some fundamnetal changes in our research direction. It was very clear to me that this was due to my questioning about that parameter. The people that I was working with knew what had happened, and I gained a lot more respect from them after that.
@Tool_maker: That's true -- but then again, sometimes the "new guy" finds problems where no one else does, simply because all the "old guys" are so accustomed to looking at the same old problems that they no longer even recognize them as problems, but "just the way things are." Sometimes experience can be just as blinding as ignorance.
William: Your story really touches a raw nerve with me. I have lost count of how many times the "New Guy" finds errors where none exist merely because he wanted to impress somebody higher up with just how much he knows. Not all new guys, but a significant number.
The problem came from assuming that the directions had been accurately followed. I had a similar problem when a new tech grabbed a stack of incomplete circuit boards from a stack and then was challenging me that my design was no good because the boards didn't work. I wound up posting a general memo that "designs will not perform as required unless they are built as designed." The lab manager challenged me as to what it was about, and I explained to him that it meant that the circuit boards would not work correctly unless all of the parts were installed. He agreed that was a correct assertion, and cautioned that tech to only use circuit boards that had passed the final inspection. The non-calibrated boards seldom met the requirements, and the incomplete boards never met them.
Many years ago a VP of engineering I knew had a sign on his office wall: "Measure twice, cut once." I memorized that one, and it's been helpful for avoiding mistakes like this one. Of course, it's easier to observe this rule when it's just you doing the measuring both times. I like the "Trust, but verify" maxim. That maxim completes the first one.
I'm not too sure how you get around this one. One company I consult for has work instructions AND a check list AND employee training AND there are still errors made relative to measurements. I will say this, we use a software package called MiniTab to perform Six Sigma calculations. With this software package, it is fairly easy to discover measurement errors. We always try to run a sample size of at least 30 pieces PER shift. Sometimes when we are checking against critical-to-quality specifications, we collect samples every hour for analysis. Another important factor, we always measure and calculate for gage R&R and factor that into analyzing the final data.
Trust, but Verify. This example belongs in a collection of wise tales and parables handed to each new measurement apprentice. When it comes to measurements, folks should not be offended when their data is double-checked but instead remind the receiver to re-check their measurements and calculations. Imagine how much unnecessary effort and research was avoided by checking the initial value...
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
