HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Rob Spiegel
User Rank
Blogger
Re: Advances in quick coupler materials
Rob Spiegel   7/27/2012 12:28:34 AM
NO RATINGS
Yes, Nancy, location is everything. a couple months ago there was a discussion about problems with a European car that was not holding up in the desert Southwest. While the car maker was happy to sell cars here, they were not testing their cars for our climate.

Nancy Golden
User Rank
Platinum
Re: Advances in quick coupler materials
Nancy Golden   7/26/2012 2:24:22 PM
NO RATINGS
I was just in Clovis a couple of weeks ago, Rob. It sure was nice - much cooler during the day and especially in the evenings than Texas at the same temperature. I think Texas humidity is a factor as well. Just goes to show that when you are designing for outdoor environments, there are all kinds of variables that need to be considered! Location, location, location!

Rob Spiegel
User Rank
Blogger
Re: Advances in quick coupler materials
Rob Spiegel   7/26/2012 1:41:58 PM
NO RATINGS
Good point on the cold weather, Nancy. It could be that the repetitive swing from hot exposure to cold exposure breaks down the material. So UV resistance may not be enough. In my New Mexico backyard, plastics don't last long. While the temperature may only be 95, the sun beating on the plastic goes to a much higher temp. 

Nancy Golden
User Rank
Platinum
Re: Advances in quick coupler materials
Nancy Golden   7/25/2012 2:14:02 PM
NO RATINGS
Probably so, Rob. The nice thing about our obstacles is that they are portable - they are easy to put up and break down in five minutes or less. If riders store them in their duffle bag out of the sun after using them - they should last for years. I think anything left baking in this heatwave will eventually have an effect. Same problem leaving them out in cold weather - pvc is known to get brittle.

Rob Spiegel
User Rank
Blogger
Re: Advances in quick coupler materials
Rob Spiegel   7/25/2012 1:20:18 PM
NO RATINGS
I would imagine the heat itself would have a long-term effect on the hoarse obstacles. So even if they're UV protected, they still may suffer from getting baked in the heat.

Nancy Golden
User Rank
Platinum
Re: Advances in quick coupler materials
Nancy Golden   7/23/2012 10:53:21 PM
NO RATINGS
I agree Rob, I really like Flow-Rite's innovation and careful consideration of both environmental factors and seeking ways to error proof connections. The Texas sun is brutal as well - I am wondering how long one can expect the UV protection to hold up and what the specs are for that type of testing...we have UV protected furniture grade pvc pipe for some of our horse obstacles to protect against degradation but extended exposure will eventually have some effect. Of course horse obstacles aren't made to withstand acid so I am guessing these couplers are pretty tough in comparison.

I also really like their ease of use - it is so nice to be able to carry out a task without having to wrestle with the connectors first!

Rob Spiegel
User Rank
Blogger
Advances in quick coupler materials
Rob Spiegel   7/23/2012 3:03:25 PM
NO RATINGS
Sounds like Flow-Rite had made some advances in the materials used in quick coupler materials. I can imagine these couplers take a beating outside in the Phoenix sun. 



Partner Zone
Latest Analysis
Just how far has handheld gaming technology come? Let's take a look inside the Nintendo 3DS XL and find out.
Design, simulation, manufacturability, and prototyping: All of these phases are being pushed forward and progressively by underlying technologies.
Wal-Mart will hold its second Made in the USA Open Call July 7-8, at its headquarters in Bentonville, Ark. The event will be a repeat effort by the world’s biggest seller of consumer goods to increase the amount of US-made products it sells in Wal-Mart stores, in Sam’s Club members-only wholesale outlets, and on walmart.com.
From design feasibility, to development, to production, having the right information to make good decisions can ultimately keep a product from failing validation. The key is highly focused information that doesn’t come from conventional, statistics-based tests but from accelerated stress testing.
There’s a good chance that a few of the things mentioned here won't fully come to fruition in 2015 but rather much later down the line. However, as Malcolm X once said, "The future belongs to those who prepare for it today."
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 6 - 10, Building Raspberry Pi Controllers with Python
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service