HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 2/2
Charles Murray
User Rank
Blogger
Re: Is aluminum strong enough?
Charles Murray   7/13/2012 6:08:21 PM
NO RATINGS
Nice story, Ann. Do you know if these pistons use cast iron cylinder liners? Going way back to the old Chevrolet Vega (does anyone remember the Vega?), engineers have tried to use aluminum. When the Vega's engine had problems, engine builders started employing the cast iron liners. In the '90s, engineers got rid of the cast iron liners and started using hypereutectic aluminum alloys for the blocks and various coatings for the inside of the cylinder, but I don't know how that came out. Are they still using the liners?

Ann R. Thryft
User Rank
Blogger
Re: Is aluminum strong enough?
Ann R. Thryft   7/13/2012 12:45:57 PM
NO RATINGS
Dave, thanks for the feedback on the re-melting process. I agree, it doesn't sound intuitively obvious as a manufacturing process. Regarding the alloy, I'd like to know, too: no details on this product were given. On the company's website appears this general statement about their aluminum pistons. but whether it applies to the new diesel piston is not clear: "We offer aluminum diesel pistons made of Federal-Mogul's exclusive, high-strength B3 alloy (2006) for high-end light-vehicle diesel applications, giving a 10 percent higher fatigue resistance at 440º C to absorb extreme loads in performance engines."

Dave Palmer
User Rank
Platinum
Re: Is aluminum strong enough?
Dave Palmer   7/13/2012 12:19:58 PM
NO RATINGS
Ann, do you know what kind of aluminum Federal Mogul is using for this application? I assume it is an aluminum-silicon alloy.  Do you know if it is hypereutectic, eutectic, or hypoeutectic? (This is metallurgy-speak for more than 12% silicon, about 12% silicon, or less than 12% silicon).

The DuraBowl re-melting process is interesting, and, like many good ideas, seems obvious in retrospect.  Doing failure analysis of aluminum pistons, I've often observed that areas which melted (in service!) are much harder and have a much finer microstructure than the surrounding area.  But I'm not sure that it would have occurred to me to exploit this as a manufacturing process.

Friction stir processing is another way to achieve improved properties in the piston bowl area.  I'm not sure whether anyone is doing this commercially yet, but there is a lot of interest in it.  At last year's Materials Science and Technology conference, Dr. Saumyadeep Jana gave a presentation on friction stir processing of cast aluminum alloys; during the Q&A session, it was clear that just about everyone in the audience (including myself!) had pistons on their mind.  I strongly suspect we'll be seeing friction stir processed pistons in the next couple years.  This would be a good topic for an article.

Ann R. Thryft
User Rank
Blogger
Re: Is aluminum strong enough?
Ann R. Thryft   7/13/2012 11:50:37 AM
NO RATINGS
The aluminum industry has been working on high-strength versions, including alloys such as aluminum-lithium, for some time now. For example, it's the major metal in aircraft, where it's mostly replaced steel (see my upcoming July feature article on aircraft materials). We've also covered a brake rotor prototype made of an aluminum composite:
http://www.designnews.com/author.asp?section_id=1392&doc_id=239090
Aluminum rotors aren't new, but this one is managing to keep up with the increasing heat requirements of today's smaller, hotter engines, not a small feat. There are some under-hood applications of plastics, including carbon composites, such as this one I wrote about
http://www.designnews.com/author.asp?section_id=1392&doc_id=243857
but AFAIK, not yet in car engines.

richnass
User Rank
Blogger
Is aluminum strong enough?
richnass   7/13/2012 10:49:48 AM
NO RATINGS
I'm a little surprised that they found that aluminum is strong enough for this application. And very pleased, asuming it can work well over time. Is plastic next?

<<  <  Page 2/2


Partner Zone
Latest Analysis
In this new Design News feature, "How it Works," we’re starting off by examining the inner workings of the electronic cigarette. While e-cigarettes seemed like a gimmick just two or three years ago, they’re catching fire -- so to speak. Sales topped $1 billion last year and are set to hit $10 billion by 2017. Cigarette companies are fighting back by buying up e-cigarette manufacturers.
Microchip recently released the 3D TouchPad, the first USB PC Peripheral device that couples 2D multi-touch input with 3D air gesture technology. The company seeks the help of developers to further enhance the capabilities of the technology.
Made by Monkeys highlights products that somehow slipped by the QC cops.
To give engineers a better idea of the range of resins and polymers available as alternatives to other materials, this Technology Roundup presents several articles on engineering plastics that can do the job.
Mac Cameron of Stratasys describes the company’s Connex3 technology, which allows users to 3D-print complex parts in one build with no assembly required.
More:Blogs|News
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 20 - 24, How to Design & Build an Embedded Web Server: An Embedded TCP/IP Tutorial
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: 10/28-10/30 11:00 AM
Sponsored by Stratasys
Next Class: 10/28-10/30 2:00 PM
Sponsored by Gates Corporation
Next Class: 11/11-11/13 2:00 PM
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service