@Ockham: Here is an article that describes in more detail why these pistons are a big deal. Was your 7L V8 turbodiesel for racing? If so, you probably didn't need to worry too much about thermal fatigue. Also, two decades ago, you probably didn't need to worry about emissions too much.
Aluminum pistons are obviously nothing new, but in order to reduce diesel emissions, it's desirable to get piston bowl temperatures as high as possible. Unfortunately, if you get them too high, the aluminum will melt. (Also, at temperatures near the melting point, the fatigue strength of the aluminum is greatly reduced).
Interestingly enough, when the aluminum melts and resolidifies, its mechanical properties are greatly improved. This is the idea behind Federal-Mogul's Durabowl process. I have no idea how they got the idea, but I wouldn't be surprised if it occurred to someone while looking at a failed piston.
Aluminum pistons, cast, hypereutectic and forged have been standard fare for piston technology for decades, some of them in very high stress applications.
They're talking about 93kW per liter. O.K. that's a 250 hp 3 liter diesel. Great. I was getting over 600 kw out of a turbosupercharged 7 liter V8 over two decades ago, and it had typical OEM forged aluminum pistons. They seemed to hold up just fine, even with over 20 inches of turbo boost...and I did all that design with a piece of paper and a slide rule and OEM components! :-)
Aluminum blocks? So? That's no big shakes either...and long before the Vega, too. They've have been around in various GM products since the early 1960's (Buick 215, Corvair flat six, etc.)
The much maligned Vega used aluminum block and cylinder with a spray coated cylinder wall which failed rather miserably in the Vega. But (like so many other technologies prototypd on the Vega, such as the HEI ignition system) very similar technologies eventually made their way into the GM product line, like the LS1.
Pardoning the pun, why are we suddenly so gassed about an aluminum pistoned turbo diesel?
I believe the GM "LS" series V8 engines used in rear-drive cars since 1997-1998 is an all-aluminum block (no iron cylinder liners). It was first used in the 1997 Corvette. The LS engines are used in the current Corvette and Camaro high-performance cars.
Personally, I own a 1998 Chevrolet Camaro Z28 that is factory equipped with the LS1 5.7 liter V8 with aluminum block and heads (and 6-speed manual transmission). I have 135,000 miles on the car, and it still runs like new...brutal power and acceleration by normal car standards.
For most GM truck applications, the LS engine blocks are cast iron.
During the late 1970's, I had a 1973 Chevrolet Vega with the aluminum block. It drank about one quart of oil for every 100 miles, due to the aluminum cylinder wear.
@Chuck: Yes, Mercury used their proprietary Mercosil low-copper hypereutectic alloy, along with a nickel-based piston coating, for some 15-25 HP engines in the late '90s. As far as I know, they never used it outside of that horsepower range. I'm not quite sure why it hasn't been more widely used, since it does seem to have offered a number of benefits.
Mercury's decision to keep most of their casting in-house and to develop it as a core competency has paid off; the Mercosil alloy is sold commercially, along with a series of die-casting alloys, called Mercalloy, which Mercury developed. Mercury casts these alloys for outside customers, and also licenses the alloys to foundries.
While Evinrude closed its die-casting division prior to the OMC bankruptcy, they have held on to their lost-foam casting facility; in fact, they recently won Best-In-Class in the AFS Casting of the Year competition. Like Mercury, they also do work for outside customers.
Thanks, Dave, for stirring my memory a bit. I do recall the outboard engine industry using aluminum alloy blocks. I looked back at an old article (from the '90s) and found that Mercury Marine was using (and maybe still uses) a hypereutectic aluminum-silicon block alloy known as Mercosil. Those engines went into production in '94. The silicon in the block was supposed to enhance wear resistance. Later, they used a nickel phosphorous/boron nitride piston coating with no cylinder liner, but I don't know how that turned out, or whether they still use it.
@Chuck: I can't speak for the auto industry, but in the outboard engine industry, the status quo is a block made out of a lost-foam cast or die-cast alumium alloy (typically A356), a cast iron cylinder sleeve, and a hypereutectic aluminum alloy piston. However, Yamaha has started to use plasma-sprayed cylinder liners instead of cast iron sleeves. I believe the technology they use was developed by Ford and Flame-Spray Industries. Sulzer Metco has a different plasma-sprayed cylinder liner technology. One of the advantages of the plasma-sprayed liners is that they save weight compared to a cast iron sleeve. The properties of the coating be tailored to get additional benefits.
BMW Motorcycles ran an all aluminum block with no cast iron liners with great success. I've seen them run over 100,000 miles with no loss of compression. I don't think the problem is purely aluminum but the overall design of the combustion process. The normal diesel "crack" that occurs at the time of ignition created enormous stresses in all the metal in the combustion chamber, not just the piston; spreading this explosion out over time would go a long way toward reducing stress. I'd guess that BMW has adopted more than just a triple turbocharger and an aluminum piston to make this engine meet their performance goals. Using aluminum pistons and reducing reciprocating mass is a significant step toward increased performance and durability.
Some cars are more reliable than others, but even the vehicles at the bottom of this year’s Consumer Reports reliability survey are vastly better than those of 20 years ago in the key areas of powertrain and hardware, experts said this week.
Many of the materials in this slideshow are resins or elastomers, plus reinforced materials, styrenics, and PLA masterbatches. Applications range from automotive and aerospace to industrial, consumer electronics and wearables, consumer goods, medical and healthcare, as well as sporting goods, and materials for protecting food and beverages.
While many larger companies are still reluctant to rely on wireless networks to transmit important information in industrial settings, there is an increasing acceptance rate of the newer, more robust wireless options that are now available.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.