Bobjebgr, I think you're right about figuring out how composites will age in space: this is all pretty new and the NuSTAR satellite (as well as the Juno satellite) is an experiment in that direction. Composites have been used in aircraft for several decades, so there's already a lot of industry knowledge about wear due to UV and strikes. Regarding NuSTAR details, you may find answers at the link to the NASA site we gave in the article. There's also some discussion in the comments to the Juno spacecraft article: http://www.designnews.com/author.asp?section_id=1392&doc_id=244386
Good article Ann—one thing interesting to me is how composites will hold up relative to their environment. I suspect the ability to judge the aging process of the composites used for the satellite, while in space, is basically a guessing-game. I'm talking specifically about UV and radiation received by the structure as years progress. Another factor, strikes by debris and very small projectiles (meteorites) flying by. Ann, do you know if there are sensors to indicate "hits" taken by the satellite while in use? Also, are there mechanisms that will gage degradation and aging?
I'd think that new material interfaces would be fully tested, in simulation and in flight testing, at various stages, which is why this failure seems surprising.
Oh, one more thing for Airbus, how is it allowed in hardware/software that a rudder command can make the tail, ie., vertical stabiliser fall off? (New York crash).
I'm sure that Airbus will address the composite issue, and it is a materiel interface problem, awfully hard to predict.
Rob, I agree about the NASA endorsement. I was excited to see that several instrument benches were made of composites on this satellite, as is the optical bench on the Juno.
notarboca, if you're referring to the Airbus wing failures http://www.designnews.com/author.asp?section_id=1392&doc_id=245829 those were not caused by a composite problem, but by a problem with an apparently mis-spec'ed aluminum alloy and the misunderstanding on the part of design engineers about how to interface that alloy with composites. Also, it took 10 years for that problem to show up, and so far there have been no accidents caused by it. Personally, I'm more concerned with the airlines' lowered maintenance standards for commercial aircraft.
Thanks for your input, naperlou. Aerospace composites aren't particularly new, as you rightly pointed out. But making all or part of the booster/launch vehicle out of them is definitely new.
Also, Chuck, this application shows a lot of confidence in the durability of composites. I wouldn't think NASA would use it if it didn't beat or meet the durability of alternatives.
I will be the first to say that I am scared to death of flight composites (see Airbus failures, give me a DC-9 (shut up old man :-)), but I am also aware that these are amazing pieces of hardware. Congrats on the phenominal achievement of space-rated composites!
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
