i worked in an open pit copper mine and the trucks we used had a gross wt 0f 300 tons loaded uphill and 150 tons empty yet their diesel-electric system included 100% retarding i.e. electric to resistance braking which was effective up to 40mph downhill to a 2-5mph stop. then you'd use the hydraulic brake. pretty cool eh ?
Certainly transit systems, Metro's in particular, are huge power users. The shorter the vehicle headways, the greater the potential benefit & ROI, methinks. Couple this with more electrically efficient aluminum/stainless steel 3rd rail (compared to the steel rail still in use on many systems) and you could reap some significant benefits.
There may also be an opportunity for this technology with ship-to-shore cranes or intermodal facility cranes where high duty cycle, repetitive lift & drop motions of heavy containers would make good use of energy storage & retrieval. Slab handling or ladle cranes in a steel mill may also be good candidates for this technology.
The amount of energy turned into heat in a standard braking system is very large. Most regenerative systems that store it in batteries are unable to recover very much of it because the battery can only accept so much charge. How much energy? consider that a freight train may spend ten minutes getting up to speed, and yet do a fast stop in thirty seconds or less. Think about a passenger car, possibly ten seconds for zero to sixty MPH, but in a panic stop, sixty to zero in much less time. The limitation is always in the energy conversion process, it appears. Asking an inverter that delivers up to 10KW for an acceleration to convert 50KW back into electrical power is asking for component failure unless the system is built for much more than the driving loads would ever be.
Forcing power back into the grid is a similar situation, in that each element is only sized for driving power peaks which are usually much smaller.
Railroads have used regenerative braking with energy recovery for years. The Northern Pacific used it going over the Rockies: the downhill train was pushing energy into the overhead wire which was used by a train coming uphill. The high cost of maintaining the overhead wire was the eventual demise of this operation. Other locations tried this but found the ROI did not justify the expense. Currently, I don't recall any major railroads or shortline freight railroads that use electric power as their principle energy source.
In the Northeast, the electric trains are for passenger operations. These are either 600 Vdc for subways and other third rail operations or about 11,000 Vac, 25 Hz, for the overhead wires. In the subways, the grades as slight and the trains relatively light. Trains are frequent. This may help with using regerative braking with energy recovery. The problem is that many of the old subway cars are not designed and built to provide regenerative operation. With the units operating on 25 Hz. power, the trains are more widely distributed. For these trains, regenerative braking with energy recovery must have either energy storage for the recovered energy or needs the converter stations to be able to change the 25 Hz. energy to 60 Hz. Most of the electric locomotives use dc motors and do not have inverters for regenerative operation. The point this leads to is that the locomotives and/or infrastructure will need some substantial modifications to use energy recovery systems.
One last point, many freight railroads do use regenerative braking without energy recovery. It is dynamic braking where the recovered energy is converted to heat and dissipated into the air.
I have a friend who works with heater strips that place them on rails to keep ice from causing wheels to spin in train stations. I could see this little bit of accumlated energy created by braking being used to power this system at the stations. Or maybe use this energy to keep the lights on and heat/AC going in the cars while sitting in train stations rather than using the engine power. The list goes on and on and the needs are everywhere!
How about piezoelectric generators under the tracks for when these hugh masses move over them? It probably doesn't meet the ROI, but like capturing energy from the sun, waves, water, and oil, it starts somewhere!
Festo's BionicKangaroo combines pneumatic and electrical drive technology, plus very precise controls and condition monitoring. Like a real kangaroo, the BionicKangaroo robot harvests the kinetic energy of each takeoff and immediately uses it to power the next jump.
Design News and Digi-Key presents: Creating & Testing Your First RTOS Application Using MQX, a crash course that will look at defining a project, selecting a target processor, blocking code, defining tasks, completing code, and debugging.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.