HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Page 1/2  >  >>
AJ2X
User Rank
Silver
Re: Resolution key to surgery success
AJ2X   7/5/2012 12:22:49 PM
NO RATINGS
NadineJ--

Agreed, that many articles here are indeed based on press releases, though I expect (I hope not unreasonably) those press releases to be at least looked at and vetted for technical rigor and not just passed along as fact.

Also agreed, that encouraging innovation and inquistiveness is a Good Thing.  Having one's expectations raised by overenthusiastic and uncritical PR is, however, a waste of valuable engineering time.

We'll just have to disagree on whether this is "good article."

NadineJ
User Rank
Platinum
Re: Resolution key to surgery success
NadineJ   7/5/2012 12:08:52 PM
NO RATINGS
AJ2X - I'm not getting you wrong at all.  I definitely get what you're saying.  It's unfortunate that you've labeled my post a "shill comment".  I prefer positive and respectful.

I stand by my comment that the article is a good one.  What Charles wrote is sound. Many articles here are based on press releases.  Each also gives a little more information to provide a bigger picture and encourage inquisitiveness.  That's a good thing. 

AJ2X
User Rank
Silver
Re: Resolution key to surgery success
AJ2X   7/5/2012 9:14:15 AM
NO RATINGS
Jack Rupert --

Yes, surgeries are pretty much entirely wired.  Hospitals are conservative entities, and adopt new technology like wireless slowly and carefully  -- intereference between devices can mean life or death.  Video particularly is mostly copper based, since any loss of resolution (there's that word again) or time delay between a surgeon's movements and the picture on the monitor is unacceptable, both of which can occur with wireless video as it usually is implemented today. 

Additionally, many (most?) video systems in ORs are on mobile carts, completely independent of any servers or permanently-installed monitors.  A camera, light source, recorder/printer and monitor all reside together in a cart to be moved rapidly from OR to OR as needed.  A single power cable is plugged in, and it's ready to use.  A second, coax video, cable could extend to a built-in video system if wider viewing or monitoring is required.  Very little compelling need for wireless links.

AJ2X
User Rank
Silver
Re: Resolution key to surgery success
AJ2X   7/5/2012 9:01:30 AM
NO RATINGS
NadineJ --

I did note the "if" in your statement, which is a throwaway word here to emphasize the statement about "exponentially better picture".  Nowhere in the article is "exponentially" used, so it looked to me like you were trying to claim even more amazing things for this product.  It looked like a shill comment to me, which I don't think was your intention.

Don't get me wrong -- this irtem from Omron is no doubt a useful device, and I can see places where it might be productively used.  But the claim that "Digital signals typically travelled over copper-based cables, and resolution was lost in the process" is just not accurate.  Technically inaccurate statements and publicity flack do not make a "good article."

NadineJ
User Rank
Platinum
Re: Resolution key to surgery success
NadineJ   7/4/2012 4:19:53 PM
NO RATINGS
AJ2X- I used the word "IF" because I actually read your post I tend to reply to the conversation as a whole unless otherwise specified.

My reply to the article is "If it gives an exponentially better picture, that's great news for telesurgery too."  What's to disagree with?

These conversations/posts go off topic when we start typing before fully reading and comprehending what we're replying to.

It's a good article about Omron's new offering.

Jack Rupert, PE
User Rank
Platinum
Re: Resolution key to surgery success
Jack Rupert, PE   7/4/2012 1:31:22 PM
NO RATINGS
Is surgical video all wired?  That would seem to be the only application for this device.  Although I assume that going wireless would compound the problem.

AJ2X
User Rank
Silver
Re: Resolution key to surgery success
AJ2X   7/3/2012 12:40:44 PM
NadineJ -- This device, inserted in a digital video transmission system,  cannot deliver any improvement in video resolution.  The resolution is set by the camera  -- anything added to it can only degrade the resolution or at best maintain it.

Long distance digital video transmission by optical fibers (and other means) is pretty well-established and successful, and has and will work well for telesurgery and robotics.

AJ2X
User Rank
Silver
Re: Resolution key to surgery success
AJ2X   7/3/2012 12:33:32 PM
NO RATINGS
dbarto; You are correct about HDMI having signal-quality degradation over distance in wire, as all signals do without repeaters or equalizers of some sort.  Optical transmission is better at that sort of thing, though it needs repeaters also.  But the claims for this optical device were about resolution improvements, and it cannot deliver that. 

Incidentally, HDMI is not common in laparoscopic camera-aided surgery -- it's mostly HD-SDI in the US and DVI-D in Europe.  And the explosive-gas argument is a non-issue: ORs have long been full of electronic equipment operating at much higher voltages and powers than are present in any video transmission method.

NadineJ
User Rank
Platinum
Re: Resolution key to surgery success
NadineJ   7/3/2012 12:06:18 PM
NO RATINGS
If it gives an exponentially better picture, that's great news for telesurgery too.

Any information about this being used with robotics in remote controlled surgeries?

Ann R. Thryft
User Rank
Blogger
Re: Resolution key to surgery success
Ann R. Thryft   7/3/2012 11:45:57 AM
NO RATINGS
Thanks for this, Chuck, this is an exciting development in vision technology. Interesting that the technology comes from Omron; they make a lot more than just imaging equipment.

Page 1/2  >  >>


Partner Zone
Latest Analysis
It's been two years since the Mac Mini's last appearance on iFixit's teardown table, but a newly revised version joins Apple's lineup this week.
More often than not, with the purchase of a sports car comes the sacrifice of any sort of utility. In other words, you can forget about a large trunk, extra seats for the kids, and more importantly driving in snowy (or inclement) weather. But what if there was a vehicle that offered the best of both worlds; great handling and practicality?
Kevin Gautier of Formlabs describes the making of a carbon fiber mold for an intake manifold, using a $3,300 3D printer, during Medical Design & Manufacturing Midwest.
Science fiction author Isaac Asimov may have the best rules for effective brainstorming and creativity. His never-before-published essay, "On Creativity," recently made it to the Web pages of MIT Technology Review.
Much has been made over the potentially dangerous flammability of lithium-ion batteries after major companies like Boeing, Sony, and Tesla have grappled with well-publicized battery fires. Researchers at Stanford University may have come up with a solution to this problem with a smart sensor for lithium-ion batteries that provides a warning if the battery is about to overheat or catch fire.
More:Blogs|News
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 20 - 24, How to Design & Build an Embedded Web Server: An Embedded TCP/IP Tutorial
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: 10/28-10/30 11:00 AM
Sponsored by Stratasys
Next Class: 10/28-10/30 2:00 PM
Sponsored by Gates Corporation
Next Class: 11/11-11/13 2:00 PM
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service