The thing that bothers me is that I'm getting use to products that don't work or don't work properly. It appears that some companies basically skip the field test or consumer focus groups that find errors in engineering and / or manufacturing. Would we be so forgiving if the end product was an MRI or an aircraft engine? If the resulting error created false readings or dangerous conditions would we not be more rigorous in our efforts to provide the best product available? I know salt shakers are cheap but it seems solutions are available at the manufacturing level.
I think we may be too used to having every cheap thing be perfect. But it is good to read this article to make sure we look at these lids, which every house uses by the hundreds, and make sure ours are "perfect." Now I can make them perfect. Thanks for the tip!
The worse case for me is when it was either specified too large, or the mold was too large, or the plastic shrunk and the lid doesn't tighten but spins. I don't think I ever had one too small, however.
Here in Hawai'i, a non hermetically sealed container of salt becomes a damp container of salt water in a few days. I've tried various sealed containers, ( snap lids with o rings, etc... ) but keeping the salt in the refrigerator works fine. Keeping lidded salt containers on the table is just a fantasy.
For a real laugh, check out the Trudeau syrup dispenser. My business partner purchased this lidded pitcher with eight separate, dishwasher friendly plastic parts, including a threaded base assembly with o-ring. It never quite goes together well enough to not leak and never quite re-assembles well enough to be useful. After cleaning the refrigerator shelf a few times, I threw it out and use a simple, leakproof pitcher whose design hasn't changed much in the past 3000 years. I'm sure someone got a nice design award but they should be made to use it a few times.
Low-sodium foods are higher in calories to balance the removal of salt so consumers will experience the prepared food as tasting equally yummy. The levels of salt in prepared foods are quite high, or at least used to be, so there's a lot of "yummy" to make up for.
The problem COULD have been solved very early in the design/build process IF the tool designers specified a D-M-E RUNNERLESS moldbase w/ proven cavity probes!
Larry M; It makes sense that the rice would eventually need to be either replaced or 'refreshed'. The process could be to completely empty the salt shaker and refill it with a fresh salt / rice mixture. Then the 'stale' salt / rice mixture could either be discarded or baked to refresh the rice. It could become very complicated for something as cheap as salt.
It is certainly true that a hot wire would be the best method for cleaning off mold flash in a production environment, in fact it could probably be an automated process. But I very seldom have a hot wire in my pocket, in fact, I carefully avoid having hot wires in my pocket. But a good sharp pocket knife is useful in many situations, and is a very handy tool. Of course, there are indeed a lot of folks who should never handle any tool sharper than a tennis ball. So it would indeed not be the best tool for everybody.
GlennA wrote: "So eventually, the salt shakers were full of rice, with a few grains of salt in between. Apparently, no one realised that only the salt needed to be replaced."
Nope, Glenn, that's not right. The rice absorbs only a finite amount of water and needs to be replaced periodically (or baked in an oven at, say, 180, for several minutes to drive off the water). The error was not in refilling the shakers with salt/rice mixture, but in failing to pour out the old rice first.
William K. wrote "It should not take more than a few seconds with a sharp knife to trim the runner remains so that they never catch in the threads,..."
Actually it's much more common in production to use a hot wire. The heated wire segment is stationary on the bench and the operator just passes the objects to be trimmed across it. This is safer than a knife for at least two reasons:
The wire is stationary. You don't have two hands working against one another with potential to slip.
The wire can have guards wide enough to pass the object to be trimmed but narrow enough to block fingers.
Now there's a bloody story, Chuck. I was given a winter coat as a gift. It was too big. I took it back with the receipt and they wouldn't take it back because it had picked up some dog hair from my back seat. I took it outside, brushed it off and took it to another clerk who accepted it.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
