HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 3/3
NadineJ
User Rank
Platinum
Re: Poorly designed container wasteful
NadineJ   7/3/2012 11:30:43 AM
NO RATINGS
Beth-the problem you had may be poor design but it also may be a prankster depending on the circumstance.

I've never seen this as a problem, but I'll pay more attention.

Tool_maker
User Rank
Platinum
Re: Container Engineering vs. the Actual Product:
Tool_maker   7/3/2012 10:59:19 AM
NO RATINGS
Reese's salt is not the only product that has done this to mee, it was just the last one before I submitted the article. It has also occured with cheap spices purchased at Dollar General stores and Lawry's Season salt. So it does not appear that the price of the product is the soul determining factor in the problem.

As for your work_arounds, I make my living punching, bending and forming steel products and have always considered plastic mold work to be witchcraft anyway, so I bow to your superior knowledge.

Ralph

Mydesign
User Rank
Platinum
Moral of the story
Mydesign   7/3/2012 5:06:29 AM
NO RATINGS
1 saves
Ralph, normally excess salt intake can cause a high BP in long run. Now container also can increase the BP, so moral of the story is both salt and containers are not good for health.

GlennA
User Rank
Gold
salt shaker tangent
GlennA   7/2/2012 3:53:00 PM
NO RATINGS
Many years ago, on my first trip to Houston, TX, I noticed the salt shakers had rice in them.  When I asked why, I was told the rice absorbed the humidity, so the salt would not clump.  However, re-filling of the salt shakers was done with more of the salt/rice mixture.  So eventually, the salt shakers were full of rice, with a few grains of salt in between.  Apparently, no one realised that only the salt needed to be replaced.

Rob Spiegel
User Rank
Blogger
Re: Poorly designed container wasteful
Rob Spiegel   7/2/2012 3:12:06 PM
NO RATINGS
I guess I've been lucky. I use dozens of these types of shakers for everything from  salt to habanero powder (which would be quite a problem if it came out in a gush). I have not run into the problem. My guess is that it's a rare occurrence.

JimT@Future-Product-Innovations
User Rank
Blogger
Container Engineering vs. the Actual Product:
JimT@Future-Product-Innovations   7/2/2012 2:04:38 PM
NO RATINGS
It's funny – there are probably a dozen work-arounds to improve that design. Change the gate locate on the cavity; or make the part a compression molded part without a gate; just to immediately think of two alternatives  ---  but food and drug packaging design has been a long standing irritation of mine. This is just one good example.

When I buy headache or cold remedies for example, I ALWAYS choose the store brand generic equivalent. The labels always say, "Compare to the Active Ingredient of ,,,{such-and-such}".  And of course the pharmaceutical ingredients are always identical.  How then, can the generic be sold for a fraction of the national brand-?  The answer is in the packaging.  Pill bottle tops that are painful to twist-off.  Low grade adhesives on safety membranes that cause the membranes to tear before  the adhesive gives way.  Foil bubble packaging that cuts your fingers before it yields the drug within.  Its ALWAYS inferior packaging, whether by material or by design.

Recently, when I was forced to actually purchase a Name-Brand because of the generic having been sold-out, I was so happily impressed with the ease of opening the product, that I had forgotten how well engineered the originals often are.

naperlou
User Rank
Blogger
or you could try another brand
naperlou   7/2/2012 8:48:48 AM
NO RATINGS
Ralph, you bring up a good point.  The title of the article was what got me to open it.  It seems that we often run into problems with these injection molded parts.  If you make plastic models you will be familiar with the situation.  Trimming is important.  As for the popcorn salt, I would look at other brands.  It is bad enough that the salt will raise your blood pressure.  The packaging should not on top of that.

Beth Stackpole
User Rank
Blogger
Poorly designed container wasteful
Beth Stackpole   7/2/2012 8:35:28 AM
NO RATINGS
I've had the pleasure on numerous occasions of applying salt or some other spice element to food and having the plastic cap come off and dump well beyond the desired amount onto my preparation, only to have to ditch it and start again. I join with Ralph on lamenting this Made for Monkeys design.

<<  <  Page 3/3


Partner Zone
Latest Analysis
Lithium-ion battery prices will drop rapidly over the next 10 years, setting the stage for plug-in vehicles to reach 5%-10% of total automotive sales by the mid- to late-2020s, according to a new study.
Two researchers from Cornell University have won a $100,000 grant from NASA to continue work to develop an energy-harvesting robotic eel the space agency aims to use to explore oceans on one of the moons of Jupiter.
Is the factory smarter than it used to be? From recent buzzwords, you’d think we’ve entered a new dimension in industrial plants, where robots run all physical functions wirelessly and humans do little more than program ever more capable robotics. Some of that is actually true, but it’s been true for a while.
The big picture to this hands-on technology curriculum is to illustrate to students that the future of IoT and IoE (Internet of Everything) development can be created in today’s classroom.
A recent Design News-exclusive study proves that engineering professionals are at the very forefront of this push into the future and making direct financial, performance, and value impact on their organizations by being personally involved or final decision-makers on automation solution and component choices.
More:Blogs|News
Design News Webinar Series
5/21/2015 11:00 a.m. California / 2:00 p.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
6/3/2015 8:00 a.m. California / 11:00 a.m. New York
6/11/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jun 8 - 12, Everything You Ever Wanted to Know about Filters
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course June 2nd-4th:
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service