I have built three of these and they serve my needs quite well, but I will accept no responsibility for any injury or damages arising out of the construction of or the use of this gadget. BUILD AND USE IT AT YOUR OWN RISK! I was not aware of it when I designed this gadget, but there are commercial, UL approved products available that do what this device does. This gadget posting is for educational purposes only. Use any good ideas found in it, but DO NOT BUILD IT! Use of this device may void your fire insurance.
Thanks! I mounted the sensor inside the box because the circuit is not isolated from the power line. The circuit does not require a regulated 24 volt power supply. The power supply voltage only affects the heat generated by the 6 volt zener regulator, being used as a thermal air pump. Using a microcontroller and a thermistor would not affect this situation. If the sensor is mounted outside the box, or fast sensing response is not required, the 6 volt regulator can be moved to the power unit and the problem goes away entirely.
I frequently work with PIC microcontrollers (see GF#192 and GF#198) and could have gone that route. If I can do the project simply without a microcontroller, I prefer to do it, because not all Gadget Freak readers have the means to program a microcontroller.
This analog circuit is closed-loop and is capable of very high precision.
A microcontroller with a thermistor circuit definitely would resolve the voltage regulator temperature sensitive because temperature monitoring closed loop detection can be embedded within the software code. The closed loop circuit will definitely impact the project BOM cost. Very nice project though!
Note that when the unit is first plugged in, you must wait at least a half hour for the temperature setting to stabilize. The voltage regulator circuit beneath the hole in the top of the box is located there in order to pull ambient air through the box, but it also heats the box up a bit. This "thermal air pump" was created to speed up the thermostat's response. This wasn't an issue when the circuit was an open breadboard, but enclosing the sensor in the box greatly increased the delay and therefore the temperature overshoot (using a forced-air heater). With the thermal air pump, the response of the thermostat is quite good. With a slow heater, like an oil-filled radiator, the thermal air pump won't be needed and the voltage regulator circuit can be moved to the power unit, if desired.
I use my thermostats with the hysteresis mostly bypassed. That means that the jumper is shorting pins 2 and 3 of J2. This means that the hysteresis is determined by the Thevenin equivalent of R2 through R6 and by R9. This is sufficient for my needs, as I want precise control. I left the option available for increasing the hysteresis in case a user finds that the heater is switching on and off too often.
The SCR voltage regulator is a bit temperature sensitive, which could slightly affect the thermostat's set-point. This will affect the internal heating of the control unit, due to the thermal air pump. The temperature coefficient of the SCR regulator is -80mV/degC. Once the thermostat is stabilizing the room temperature, this won't be an issue at all. If you turn the heater on in a cold room, the thermostat will think the room is a few degrees warmer than it really is and shut off prematurely. Within a half hour, the set-point will stabilize at its proper value. I didn't find this to be a problem because I keep my rooms regulated, but if you do have a problem with it, replace the SCR, R19 and R20 with two 1N4742 (12V, 1 watt) zeners in series. Of course, the standby power consumption will be increased a little bit and the zeners won't be as robust against power surges as the SCR. Definitely use the zeners if you intend to put numbers on the temperature dial.
What's maddening is you can't anticipate where trouble will come from. In Chuck's Toyota floor mat story, the car company is running a recall because an floor mat not designed for the car model could bump into the accelerator.
Never say never when it comes to lawsuits and ridiculous awards. What do hot coffee, circular saws, lawn mowers and highchairs have in common? All were at the base of some outrageous jury awards. Who would have ever guessed that you can get burned by hot coffee?
I would not lose any sleep over it though, because you do not have enough cash to attract one of the real blood sucking attorneys.
Yes, I do plan to make some more gadgets. Currently, I'm desinging a 3000 lumen flashlight with a detachable burning laser. Would that make a good project?
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 4
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
