BAD NEWS.. not only Audi but also ANYTHING... CHRYSLER; it happens to the Caravan, Voyager, Jeep Cherokee... the double filament rear light bulb that act as Rear lights and Brake lights, is mounted in a plastic bulb holder that has a bayonet style mount into the rear lamp assembly connected to the car electric system, well the bulb holder has 3 sliding contacts that touch the lamp assembly, well it seems that the current flowing to the bulb, gets the whole thing hot enough to scorch the bulb holder and melt the lamphoder where the contacts touch, resulting in NO brake light or tuning light or working rear lamp === DEALER solution : to replace (BUY $) the whole rear lamp assembly. ...
Talking about monkeys designing stuff... ! ! ! planned obsolescence, or plain stupidity.
My solution... solder 3 wires (1 regular rear light filament, 2 brake light filament and 3 ground) to the lamp holder, and connect them directly to the electric system wires spliting the insulation were the wires go into the connector. you have to know what you are doing but it solves the problem and works forever.
It isn't just Audi or Vw etc they also do the same stuff in Mercedes. I just replaced the dash light bulbs ($1 at Napa or $20 from the stealership same bulb, same brand etc) and the sockets were either scorched or melted. Of course the dealer er stealer will tell most customers that they need a new dash assembly (don't have enough room to put the price of that in one post). Unfortunetly it seems most customers are of the type that they can fix anything using only a credit card or checkbook and the problem goes away. Some of the rest of us who have an idea whch end of a screwdriver or soldering iron to hold are converting to LED's. That isn't as straight forwards as it seems. Mercedes has designed the systems so that they detect the current load so if you don't get things right you get light but still get a light out light unless you are lucky to have that one burnt out as well !
Funny all through school up to university not one person ever told me there are monkeys in Germany ;-]
I was surprised to see that this failure was on an Audi. Audi is a high dollar vehicle that you would not expect to see a failure like plastic creep. Unfortunately, limitations of plastic as compared to metal are not always taken into account when metal replacement projects are completed.
When I started out, my first professional job was working in an automotive paint lab in Detroit. Knowing that the cars would experience the combo of salt and humidity in climates such as Florida, we did saltwater testing on the paint. Seems a no-brainer to test for all of the potential environments customers will use the products.
When I started out, my first professional job was working in an automotive paint lab in Detroit. Knowing that the cars would experience the combo of salt and humidity in climates such as Florida, we did saltwater testing on the paint. Seems a no-brainer to test for all of the potential environments customers will use the products.
Thanks, thrashercharged, I didn't really think 1 deg C was low enough based on what Chuck and others had said. Now I'm curious--where are you writing from?
J-Allen thinks the engineer should be publically whipped. I think the engineering (and higher) management needs to be tortured.
I've been involved in too many projects where NO time was allocated for testing/debugging. If the thing looks good the first time the management is ready to move on. I'm all for designing something as close to the final product as possible but a lot of engineering departments already have the NEXT project to shift you to and leave no time for a second rev.
I suspect that the plastic compound that ended up in the tail light assy. probably cost 10 cents per pound less than the one they had been using for 20 years.
"Re UK temps, parts of northern Scotland are pretty darn cold in the winter, down to an average of 1C or below, but that may not be low enough for testing purposes."
1 deg C? Oh no, that's not nearly cold enough! 1C is almost considered tropical in some areas of the north! When it warms up to above freezing for the first time in the Spring we start wearing T-shirts, really! -40 is the typical cold standard. Most car manufacturers have a hot and cold weather proving grounds. GM's cold weather proving grounds is in Kapuskasing, Ontario, Canada.
While plastics have come a long way in the last decade or so. there are just certian components that exceed the capabilities of even the best plastics. Light bulb assemblies in this case are a classic example. Had the manufacturer chosen LED lights instead of high heat conventional bulbs, this may have worked fine. Apparently verification testing has gone by the wayside in favor of cost cutting.
Other components that makes me nervous are plastic valve covers and intake manifolds. they may work fine for a few years until the warranty expires, but eventually time and thermal cycles will do them in, leaving the owner footing the bill for replacement parts.
Re curiosity vs cleverness, I was assuming pre-existing curiosity, expertise and a few other things on the part of the clever fixer, otherwise he/she couldn't express their cleverness and provide a useful fix. Re UK temps, parts of northern Scotland are pretty darn cold in the winter, down to an average of 1C or below, but that may not be low enough for testing purposes.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
Researchers at MIT and Sandia National Labs have observed a reaction in lithium-air batteries that could help improve the design of these cells for electric vehicles and other applications.
Healthcare might seem to be an unlikely target application for the Internet of Things technology, but recent developments show small ways that big-data is going to make an impact on patient care moving into the future.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
4 
