HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  RESOURCE CENTER  |  INDUSTRIES
Page 1/5  >  >>
User Rank
Gold
Re: Bob Pease must be rolling in his grave.
8/20/2013 1:03:45 AM
NO RATINGS
78RPM

Iagree, photoresistors response time is quite slow when reacting to sunlight. IR LEDs maybe a better choice because of their fast respones time and wavelength associated with the sun. I know Forrest Mims have done a lot of work in sun tracking using IR LEDs as well as traditional red LEDs. You should be able to find his published worked on this subject at his websites listed below.

http://www.forrestmims.org/

www.sunandsky.org

User Rank
Gold
Re: Bob Pease must be rolling in his grave.
8/7/2013 5:18:14 PM
NO RATINGS
mrdon, I actually started my project by trying to use two pairs of photoresistors to find the sun -- one pair for vertical and a pair for horizontal.  I discovered that photoresistors are too imprecise and too non-linear.  They always ended up cockeyed.  If you wish to point a parabolic cylinder at a water pipe, your aim must be within 3 degrees of error.  I may publish a revision showing how to use Gray code converters to sense and control position.  I would probably take the easy way out on a second pass and just use an Arduino board.

User Rank
Gold
Re: Bob Pease must be rolling in his grave.
8/7/2013 5:11:20 PM
NO RATINGS
@charly5139  Pointing a collector directly at the sun is more complicated than you assume. Your clock method would work if:

1. The earth were a cylinder.
2. Its axis of rotation is perpendicular (90°) to its orbit.
3. Its orbit is a circle.

None of these is true. Earth is approximately spherical;  It is tilted by ~23.5°;  Its orbit is elliptical.  You can find C programs online for calculating the sun position. It takes about 9 pages of C code.

If you have a parabolic channel and wish to focus the sun along a water pipe, your aim must be less than 3 degrees in error.  See http://www.analemma.com/ for a good explanation of the sun's path through the sky.

User Rank
Iron
Re: Bob Pease must be rolling in his grave.
8/27/2012 11:04:50 AM
NO RATINGS
Yes!  I remember reading that article 30 years ago.  Would you be able to point me towards a copy of it?  Thanks.

User Rank
Gold
Re: Any Analog Solutions?
7/22/2012 9:34:50 PM
NO RATINGS
The motors were probably driven by discrete or IC based H-Bridge circuits. These circuits are commonly used to provide directional control for motors.

User Rank
Gold
Re: Bob Pease must be rolling in his grave.
7/22/2012 9:22:00 PM
NO RATINGS
I remembered Forrest Mims describing his solar tracking device in the defunct Science Probe Magazine. It consisted of an analog circuit driving a dc motor. The detectors for the circuit were solar cells attached to the dc motor. Based on the sun's position,  the motor will point the solar cells in the direction of the sunlight. As explained and demonstrated in this project, a small microcontroller can enhance the performance of such a basic sun tracking device. Cool project!!

User Rank
Iron
Re: Bob Pease must be rolling in his grave.
7/22/2012 5:04:59 PM
NO RATINGS
Here in Europe, I would choose a microcontroller with a built-in RTC (real-time-clock). Knowing time and date, I can predict when the sun appears on the horizon, the elevation and when it disappears again in the evening. On cloudy, rainy days it might be useful not to switch on the servos. However, if the sun shows some erratic behavior which makes it necessary to follow it by an X/Y-tracker, your circuit might be better... (but I've never seen this on our planet).

Regards

Charly

User Rank
Gold
Re: Bob Pease must be rolling in his grave.
7/5/2012 1:06:56 PM
NO RATINGS
@Jerald,

I have my old design for sure. All this interference and "chatter" can be eliminated by integration and delay of a signal that is usually splendidly done by installing a capacitor in the output driving circuit.

Best Regards,

Chris

User Rank
Gold
Re: Bob Pease must be rolling in his grave.
7/4/2012 6:45:39 PM
NO RATINGS
Hi, Chris,

I mostly agree with you. In fact, I tried connecting four photocells to four opamp comparators. I ran the non-inverting of one into the inverting of the next one in a ring.  The binary search for right/left, up/down didn't work.  It kept getting distracted by clouds and rocks and shadows and the motors went wild like a hound dog on a scent.  If anyone has an efficient analog design, I'm interested.

But, again, I'm disappointed that everyone focuses on the solar application -- but then I guess I should have changed the title.  The circuit and program is really about multiplexing in general.  When I did aircraft flutter tests back in 1980 this little circuit would have been more powerful than the DEC PDP 11/70 we were using.

Jerald Cogswell

User Rank
Blogger
Re: A question of efficiency
7/3/2012 12:54:34 PM
NO RATINGS
Thanks, Mydesign. We are certainly eager to see the gadget.

Page 1/5  >  >>

 Partner Zone
Latest Analysis
When Dick Neubert discovered that his fireplace's heatilators lost heat when not in use, he created a gadget to rectify the situation.
Microsoft will quit supporting – and patching – Windows XP in April. This may be a cruel development for plants.
Injection molding can be a powerful tool for both prototyping and production. Here are some tips on how design engineers can get the most out of it.
Truchard will be presented the award at the 2014 Golden Mousetrap Awards ceremony during the co-located events Pacific Design & Manufacturing, MD&M West, WestPack, PLASTEC West, Electronics West, ATX West, and AeroCon.
In a bid to boost the viability of lithium-based electric car batteries, a team at Lawrence Berkeley National Laboratory has developed a chemistry that could possibly double an EV’s driving range while cutting its battery cost in half.
More:Blogs|News
From Dell / Intel®
Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013    7
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
Most recent post: Ralphy Boy
From Dell / Intel®
Trey Morton, Dell, 4/25/2013    3
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
Most recent post: Cabe Atwell
From Dell / Intel®
Kirsten Billhardt, Manufacturing Industry Marketing Strategist, Dell, 3/26/2013    6
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
Most recent post: Ockham
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Dec 16 - 20, Introduction to SCADA Security
SEMESTERS: 1  |  2  |  3  |  4