I built a a simple tracker in the mid-80's using 5 small, matched solar cells, voltage comparators and two shading strips. I forget how the motors were driven, just that it wasn't very pretty and it used dual battery packs. It worked really well, though.
I've also seen a cone shaped design which had 4 parallel holes with CdS cells at the bottom and a reference cell at the tip.
Have fun making the circuit and entering the program. I hope the focus of the device shifts to its multiplexing purpose. Everyone is focused on the solar application, but the sensors can be anything.
The program compares TWO banks (vertical and horizontal) of 30 analog sensors EACH. It uses one-byte precision or a maximum of 256 digital values. 256 divided by 30 sensors gives approximately 1 in 8 chance of two sensors having the same value. If you modify the PIC program to sense all 64 possible switches of the MUX into one pin of the MCU, you should consider right justifying the bits to get 10 bits of precision or 1024 values. This involves modifying the code at comments provided in the code. Contact me with any questions.
That freon, or maybe Propane as it has some similar properties and is somewhat cheaper, solution for moving the collector is an interresting solution. I'll have to think about that one.
Yep, the analog quad cell / baffle arrangement worked well for detection but in a purely analog system, the servo motors were always being tickled. Digital lets you add hysteresis, averaging and any other sort of condition mediation you'd like. It's also stepper friendly. It works pretty well here in Hawai'i but I did much of my tracker work in Seattle, land of grey skies.
Everyone usually manages to settle on a solution that works for their situation ( cost, available parts, space, time, etc.. ) It's fun to learn from the diversity.
At 40-60K$ for a home PV system, I want to see every watt I can possibly get. I wonder if the contractor panels have to be marked" this side up"?
Nice work, Jerald. What I find interesting about your design is that it uses a solution that a human brain would use. No human would calculate the sun's position in order to find it quickly. Asking, "where's the sun?" should work for machines, too.
Nancy, I agree this is a great project. PIC processors are used a lot of places. I have played around with their development kits. It's always nice to see/read about the different projects people develop.
@kf2qd: You probably never measured the output of a solar panel when a cloud appears. It is simply actually - the output power is linear with the amount of light.
Since it does not get pitch dark when a cloud appears, the solar panel does not stop delivering power. It may be half the amount and on very severely overcast (dreadful dark grey rainy days as there are in The Netherlands) the output may be in the order of 10%, but they still deliver power.
Since the tracker should consume a minuscule amount of power, it has a very large gear reduction since it does not move fast, so it can be powered by a small motor and even that motor needs to operation only part time, there is no reason to stop tracking when "the sun disappears" behind a cloud. The power consumed by the tracker should be in the order of 1% of the array output and it has the potential to double the daily energy output - depending on latitude and shadowing.
At the end of the day the panels are typically parked in more or less horizontal position anyway, which is safety in case a storm comes at night.
Note that the tracker will not lose the sun even when it is clouded for a long time, since the sun has a predictable path. So, as long as you do not completely reset your tracker and it has either a clock or knowledge of the previus sun position it can continue to point the panels to the correct position even when it has no good measurements for some time (or ever - it may be completely based on time and latitude to calculate the sun position).
I wonder why so many sensors were used. I know that it is in theory possible to make a tracker with a single photo sensor, but the simplest systems I have seen always use two pairs of sensors, one in X and one in Y direction to find the sun when starting from any orientation.
It's me, the author again. Does anyone have a good circuit for Gadget Freak that finds the sun with analog comparators? I tried using several op amp comparators all voting on who had the brightest signal. It didn't work very well. Show me where I went wrong. Maybe you used your method for some other purpose.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
