Jack, there was no discussion about application methods, only the fact that this material can be produced in quantities for high-volume manufacturing (roll-to-roll). Applications seem to be for backplane, not frontplane, glass.
Maybe I missed it, Ann, but did you say anyplace what the process is for applying this material to its applications? There was some talk in the comments about heat, but I wasn't sure if that was for application or if there is some other means.
Thanks, that's the detail I was hoping you could tell us. Aside from the extra visibility of scratches due to the backlight/LEDs, I think your point about not being able to place the keypad flat against the glass and the ensuing air bubbles is especially important. That's not just looks, it's function that is affected.
Great question and I did not answer it with my reply.My fault.The total installation involves a clock with various functions; i.e. bake, broil, self-clean, time settings, etc.These are all indicated by LEDs when the function is activated AND there is a back light.Any scratch in the key pad overlay would be highlighted by the backlight and / or the LEDs. Another problem we have is placing the keypad completely flat to the glass, consequently not removing all air bubbles.Those can reduce the capacitive qualities and lessen the performance and certainly the timing of the function.We use a device called a laminator.It looks like a big credit card machine, the old ones anyway, in which an imprint of the card is made by moving a spring-loaded roller over the face of the card.This smoothes out the bubbles.It's also important to note that these assemblies are made in a clean room with all of the employees wearing the necessary clean room clothing.
bobjengr, thanks for that info; that's what I thought. So my question is: what's the concern about scratches on the backplane glass, vs the frontplane overlay glass?
Ann, absolutely—you are correct. There is a specific "overlay" we use on the front side but it must be protected due to scratching.One of the issues also (and it's a big one) is heat generated from the elements or burners on the maintop.Most of my clients use a 105 degree C clock but in some cases we are skirting the upper limits of acceptability relative to temperature. This is certainly true when you have a very high input burner on the right rear or left rear.We call these "master blasters".Combine that with a range hood and you can have a delicate situation.By the way, I contacted the company and they are sending me literature and design specifications.Great work on your part.You made me look like a genius.
bobjengr, thanks for the feedback, especially details about what you'd do with this material. It sounds like you would also use this for the backplane, not the frontplane, material--did I interpret your comment correctly?
Ann, great post and good information. I have two applications that might be acceptable for this type of materia. Both are glass-backed control panels that use capacitive touch to activate various controlled manufacturing sequences. The "keypads" are extremely touchy with an in-house failure rate approaching 50%. Beth brings up a very good question relative to the durability and scratch resistance of the material. Any improvement over what we are using would be marvelous. The temperature characteristics are outstanding and well within what we experience with our 105 degree C application. Many thanks for this information.
Warren, as I said to Beth, it sounds like these products may be targeted for the backplane, not the frontplane. In any case, scratches and impacts from dropping are always a problem with plastics. My RayBans do a good job of resisting both, but their light weight seems to keep them relatively undamaged.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
Researchers at MIT and Sandia National Labs have observed a reaction in lithium-air batteries that could help improve the design of these cells for electric vehicles and other applications.
Healthcare might seem to be an unlikely target application for the Internet of Things technology, but recent developments show small ways that big-data is going to make an impact on patient care moving into the future.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
4 
