HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
REGISTER   |   LOGIN   |   HELP
Page 1/2  >  >>
Ann R. Thryft
User Rank
Blogger
Re: Applying the Material
Ann R. Thryft   6/25/2012 12:24:29 PM
NO RATINGS
Jack, there was no discussion about application methods, only the fact that this material can be produced in quantities for high-volume manufacturing (roll-to-roll). Applications seem to be for backplane, not frontplane, glass.

Jack Rupert, PE
User Rank
Platinum
Applying the Material
Jack Rupert, PE   6/24/2012 2:41:58 PM
NO RATINGS
Maybe I missed it, Ann, but did you say anyplace what the process is for applying this material to its applications?  There was some talk in the comments about heat, but I wasn't sure if that was for application or if there is some other means.

Ann R. Thryft
User Rank
Blogger
Re: CORNING
Ann R. Thryft   6/21/2012 1:45:59 PM
NO RATINGS

Thanks, that's the detail I was hoping you could tell us. Aside from the extra visibility of scratches due to the backlight/LEDs, I think your point about not being able to place the keypad flat against the glass and the ensuing air bubbles is especially important. That's not just looks, it's function that is affected.

bobjengr
User Rank
Platinum
Re: CORNING
bobjengr   6/20/2012 6:15:33 PM
NO RATINGS
Hello Ann--

Great question and I did not answer it with my reply.  My fault.  The total installation involves a clock with various functions; i.e. bake, broil, self-clean, time settings, etc.  These are all indicated by LEDs when the function is activated AND there is a back light.  Any scratch in the key pad overlay would be highlighted by the backlight and / or the LEDs.  Another problem we have is placing the keypad completely flat to the glass, consequently not removing all air bubbles.  Those can reduce the capacitive qualities and lessen the performance and certainly the timing of the function.  We use a device called a laminator.  It looks like a big credit card machine, the old ones anyway, in which an imprint of the card is made by moving a spring-loaded roller over the face of the card.  This smoothes out the bubbles.   It's also important to note that these assemblies are made in a clean room with all of the employees wearing the necessary clean room clothing. 

Ann R. Thryft
User Rank
Blogger
Re: CORNING
Ann R. Thryft   6/20/2012 1:05:22 PM
NO RATINGS
bobjengr, thanks for that info; that's what I thought. So my question is: what's the concern about scratches on the backplane glass, vs the frontplane overlay glass?

bobjengr
User Rank
Platinum
Re: CORNING
bobjengr   6/19/2012 6:20:55 PM
NO RATINGS

 Ann, absolutely—you are correct.      There is a specific "overlay" we use on the front side but it must be protected due to scratching.  One of the issues also (and it's a big one) is heat generated from the elements or burners on the maintop.  Most of my clients use a 105 degree C clock but in some cases we are skirting the upper limits of acceptability relative to temperature.   This is certainly true when you have a very high input burner on the right rear or left rear.  We call these "master blasters".   Combine that with a range hood and you can have a delicate situation.   By the way, I contacted the company and they are sending me literature and design specifications.  Great work on your part.  You made me look like a genius.

Ann R. Thryft
User Rank
Blogger
Re: CORNING
Ann R. Thryft   6/18/2012 1:02:16 PM
NO RATINGS
bobjengr, thanks for the feedback, especially details about what you'd do with this material. It sounds like you would also use this for the backplane, not the frontplane, material--did I interpret your comment correctly?

bobjengr
User Rank
Platinum
CORNING
bobjengr   6/15/2012 6:08:16 PM
NO RATINGS
Ann, great post and good information.   I have two applications that might be acceptable for this type of materia.  Both are glass-backed control panels that use capacitive touch to activate various controlled manufacturing sequences.  The "keypads" are extremely touchy with an in-house failure rate approaching 50%.  Beth brings up a very good question relative to the durability and scratch resistance of the material.  Any improvement over what we are using would be marvelous.  The temperature characteristics are outstanding and well within what we experience with our 105 degree C application.  Many thanks for this information.

 

Ann R. Thryft
User Rank
Blogger
Re: Corning's Paper-Thin, Flexible Display Glass
Ann R. Thryft   6/14/2012 11:38:16 AM
NO RATINGS
Warren, as I said to Beth, it sounds like these products may be targeted for the backplane, not the frontplane. In any case, scratches and impacts from dropping are always a problem with plastics. My RayBans do a good job of resisting both, but their light weight seems to keep them relatively undamaged.

Ann R. Thryft
User Rank
Blogger
Re: Flexible Display Glass
Ann R. Thryft   6/14/2012 11:37:04 AM
NO RATINGS
Thanks, Al. Corning has been in this business a long time. I agree, it's nice to see advancements like this from a company with that track record.

Page 1/2  >  >>


Partner Zone
Latest Analysis
Today's robots should be respected, and humans should be wary of their growing skills and sophistication. Quite simply, robots are better than us in a lot of ways. Here are 10 of them.
3D printing has met up with drones in a 3D-printed UAV. University of Sheffield engineers printed the prototype drone in 24 hours from ABS plastic using Fused Deposition Modeling.
Product design is changing with advances in technology and outsourced manufacturing. The Art of Product Design spells out the future of design engineering.
AMD is set to launch the industry's first 16 GB workstation graphics card -- the W9100.
Samsung's 5th-generation Android-based Galaxy smartphone includes a fingerprint scanner, updated camera and display, and water/dust resistance.
More:Blogs|News
Design News Webinar Series
3/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
2/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
12/18/2013 Available On Demand
11/20/2013 Available On Demand
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Apr 21 - 25, Creating & Testing Your First RTOS Application Using MQX
SEMESTERS: 1  |  2  |  3  |  4  |  5


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: April 29 - Day 1
Sponsored by maxon precision motors
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service