Thank you, Jason. My philosophy is already that the easiest way to make me do something is to claim that I can't. I am interrested in other ideas, so I dont mean to offend anyone who posts one.
As for the "horseshoe" cores, I dont know where to get any, and I'm not sure why the schematics werent posted. I sent them in with the build instructions. If you do want to make one, you can find the original article that I wrote on MAKE:projects. (It was written before this one was posted). The transistors actually work okay, as my current unit still runs cold after about 3 months of use. It may not be the "best" way, but it doesn't require any fancy or unusual components.
The efficency of the lantern itself is actually super high. The circuit with a fresh alkaline AA will last about a full week before running out. As for ICs I dont have acess to anything beyond my local radioshack and science surplus store. This gadget can be made from most low-end electronics stores with component parts.
Yes, I had originally intended to use a core, but since the PVC cap is rounded, I cannot fit a core inside the sender coil, and the reciever coil is crowded by the circuit. Thanks for your help anyways.
John, in order to more efficiently transfer power from the primary coil to the secondary coil, you need to have a high permiability core to concentrate the magnetic fields of the two coils. That is why transformers have iron or magnetic cores. I have a Hoemedics toothbrush that uses a dimple in the housing that allows a magnetic core from the charger to closely couple the two transformer coils. The other technique is to use resonance of the two coils by adding parallel capacitors to tune the two coils to the same frequency to allow better power transfer. Good luck with your experiments.
I wonder if he could use supercaps in place of batteries and whether that would speed up charging?
Maybe the key is to get the highest effeciency LED so you can live off less power in the first place.
It is useful to have knowledge in a given field. But it can be a trap if everybody knows something that used to be true, but isn't quite now because devices have changed.
There are an awful lot of ICs out there now. Often you can trick one into doing something it was not originally designed for.
I just love our field where manufacturers shove datasheets and even samples into our hands to learn with.
Not knowing what knowledge this young man has, as Engineers in the field we need to be careful with what instructions we give him. While outside thinking is indeed necessary for innovation, a firm comprehension of the fundamentals is necessary. That can only be obtained through understanding and asking those with greater knowledge than the questor currently has.
With that said, I think it would help young Mr. Duffy out if others in our field that may have some thoughts on how to improve his charging circuit would share them with him as he may not know where to begin to change and experiment to attempt better charging times. It is another step to outside thinking as well. Learning from others and bouncing ideas off of more knowledgable people. Even if you run into someone who states, "Oh that can be done that way...", it can be turned into a "Because you said it couldn't I need to prove or disprove that to myself first!" philosophy.
Great Job on your first Gadget Freak Mr. Duffy! If you keep at the circuit I am sure you will find the answer. Ask everyone you can for clues, thoughts, and ideas on what might make the battery charge faster! And remember, like TJ says, don't take anyone's answers to heart unless you understand them and know that they apply to your question. While it is up to *you* to learn, others can help as well.
If you want to transfer more power... I suggest that you use two 'horseshoe'
shaped magnetic cores with the open ends facing each other. The best case would be if you could make them touch... but even with a gap it should concentrate the flux much more than your current design.
you might look for ferrite "C" cores, there are other shapes you could use as well.
I don't see a schematic posted... but I'd caution against paralleling transistors unless you have some series resistance (usually in the emitters) or you match them for Vbe (voltage base-emitter) drop so they share current well. If not, one will probably get more current than the rest and fail first (either shorting and killing the circuit quickly, or opening and leaving the rest to run even hotter and fail slowly...)
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
