With several brands of washers and driers, the reason that the service information is provided is that the parent company has no service people, only contractors who service all brands. So to support them they need to have that information available.They stash it inside the nachine because most folks are way to intimidated to open the cover, and many more simply throw out all of the papers that they don't understand, and also, many just throw out all of the papers that come with an appliance.
Whirlpool used to hide the servicer's instructions inside the control panel of their washing machines. Between these instructions and the timing diagram stuck to the back of the machine there was sufficient information to not only isolate to the field-replaceable unit (the $350 controller board) but to figure out which component on it (a $0.37 Triac) had failed. It did take a good bit of thinking, however.
Yes, those manuals are all over the place online. However, I've found that the forums often go into greater detail -- as in "Watch your knuckle when you undo this screw." But more to the point, the forums will let you know when it's important to also replace another part when you go to fix the part that failed.
Jon, thanks for that tip on where to find the service manual. That reminds me I once found a similar document inside a washing machine years back, also from Sears. I suspect they are right: most buyers are not engineers and/or tinkerer DYI types. Still, it would be nice to know ahead of time that you've already got the info and don't have to spend hours searching for the information online.
Good point, Rob. I was pleasantly surprised that the Sears washing-machine manual found inside the machine had so much detail. Probably created more for service people than buyers. The service tech also had a tablet computer of some sort that let him view documents and manuals.
You can also find these manuals online in many cases. You can find discussions of many of an appliance's problems in forums. I find that forums are often a better source to deal with a problem than a user manual.
When we had a sensor replaced on a Kenmore front-load washer, the service man removed the lower front panel to reveal a plastic pocket with a service manual that listed all the error codes, diagnostics, etc. Maybe Sears figured most buyers were not smart enough to look through the manual, find the problem, and try to handle it themselves. Anyway, manuals with error codes do exist, but sometimes they are hard to find. Ours is now safely in an appliance folder.
I have used the cell phone camera for disassembly documentation many times. It is a great tool to quickly note how things were together. It is great for documentingwire color locations.
I agree, Beth. Why wouldn't they make it more accessible? This is reminiscent of the stories about vehicles that had to have the engine pulled to do minor maintenance work.
I had the same error code and plugged pump screen on my 8 year old Whirlpool a few months ago.
On my model there were two screws at the bottom corners of the front kick panel below the door. I removed the two screws. Removed the kick panel and the screen assembly was right there. Then turned the bayonet style cover from the screen assembly, no hoses to remove.
I pulled a wad of lint the size of a small rat out of the screen. Replaced everything and it has run several months without problems.
I, too, am disappointed that there is no list of error codes, troubleshooting suggestions, or mention of this screen in the literature that came with the washer.
As an added bonus, a foul odor that came from the laundry room vanished when I cleaned the screen.
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 4
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
