When I used mousetraps it was easy to find the dead mice. But when they crawl into the wall to die after being poisened, it's not so easy. I could always locate the area, but I didn't cut through the wall. So I quit using poisen.
My guess is that it did, until it was thouroughly dessicated by the current passing through it. We had just rented the house, and the cooked rat in the range came with it. Who can account for some people not investigating smells. I have always tried to locate the source of any unusual odors, whether foul or pleasant. In fact, I have often located the failed component on circuit boards by the smell, usually confirmed by either discoloration or deformity caused by the overheating when it failed.
I would think the rat would stink and alert the occupants that something was amiss behind the stove. I once used rodent poisen to get rid of mice. They would eat the poisen, then crawl into the walls to die. We could smell them for a week, but we couldn't get to them.
When I was a young teen, we moved into a rented house, where the electric range did not work properly. On pulling the range out from the wall, we found a rat that had been electrocuted and cooked across the terminals where the 240 VAC feed from the wall socket connected inside the range.
"A good example of what happens with the latter (self-reset) type can be found in most lamp ballasts: we've all seen fluorescent and other discharge-type lamps that SLOOOOOOOOOWLY cycle on and off all by themselves as the ballast and/or lamp gets old and triggers the device during "normal" operation. It's especially annoying in vapor-discharge (mercury or sodium) street lights (even more so if it's the one right beside you bedroom window!). "
Actually in this case it isn't a reseting cutout but a fundamental property of the gas discharge lamp. As the lamp ages the voltage required to maintain the arc discharge rises, eventually (about 20k-25k hours for HPS lamps, about 3/4 that for mercury & metal halide) reaching a level higher than the max running voltage available from the ballast and the arc extinguishes. The discharge tube then cools to a point that the arc can be restruck by the ballest whereupon the lamp's arc tube reheats and the cycle repears. The solution is to relamp the fixture.
I thought that was a huge disappointment when it was cancelled, Ratski. So instead of Texas, Europe gets all the glory, all of the jobs, and all of the resulting technology.
At least your dishes should be super clean as they were being sand blasted as well as washed. The each little chip probably became part of the blasting process. I wonder just how far it would have gone before blowing a hole through the door. Just a thought.
The Superconducting Super Collider (SSC) (also nicknamed the Desertron[1]) was a particle accelerator complex under construction in the vicinity of Waxahachie, Texas that was set to be world's largest and most energetic, surpassing the current record held by the Large Hadron Collider. Its planned ring circumference was 87.1 kilometres (54.1 mi) with an energy of 20 TeV per proton. The project's director was Roy Schwitters, a physicist at the University of Texas at Austin and Harvard University. Dr. Louis Ianniello served as Associate Director.[2] The project was cancelled in 1993 due to budget problems.[3]
Waxahatchie is about 30 miles due south of Dallas, and certainly would have both fire ants and sandy/shifty soil structure. I suspect part of the "budget problems" was failure to see how expensive solving foundation problems would be! Typical government boondoggle IMHO. Thought so at the time, still do!
I'm afraid neither I nor Google can remember or find anything about that! Try Snopes; sounds like an (non)urban legend! There may have been other reasons. Most of Texas has relatively unstable soil formations (that's why few newer houses have basements, because the codes now require floating slab foundations).
Most transformers of this type need to have such a device to get their UL/CSA approvals. The unfortunate part about this particular one was the manufacturer's choice to use one embedded deep within the windings (presumably at the potential hottest spot), and to use a non-self-resetting one. This unit was potted, so I wasn't about to try to rewind it! A good example of what happens with the latter (self-reset) type can be found in most lamp ballasts: we've all seen fluorescent and other discharge-type lamps that SLOOOOOOOOOWLY cycle on and off all by themselves as the ballast and/or lamp gets old and triggers the device during "normal" operation. It's especially annoying in vapor-discharge (mercury or sodium) street lights (even more so if it's the one right beside you bedroom window!). However, I suppose that's better (from a safety standpoint) than a street light that's out and stays that way!
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
The 3D printing revolution seems to have a knack for quickly moving technology ahead by way of collaborative effort and even a little friendly competition -- all of course in the name of scientific advancement.
Advantech has launched a new series of motion-control I/O modules to meet the increased demands that come with more distributed industrial systems that require control of a growing number of axes and devices.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
