When I used mousetraps it was easy to find the dead mice. But when they crawl into the wall to die after being poisened, it's not so easy. I could always locate the area, but I didn't cut through the wall. So I quit using poisen.
My guess is that it did, until it was thouroughly dessicated by the current passing through it. We had just rented the house, and the cooked rat in the range came with it. Who can account for some people not investigating smells. I have always tried to locate the source of any unusual odors, whether foul or pleasant. In fact, I have often located the failed component on circuit boards by the smell, usually confirmed by either discoloration or deformity caused by the overheating when it failed.
I would think the rat would stink and alert the occupants that something was amiss behind the stove. I once used rodent poisen to get rid of mice. They would eat the poisen, then crawl into the walls to die. We could smell them for a week, but we couldn't get to them.
When I was a young teen, we moved into a rented house, where the electric range did not work properly. On pulling the range out from the wall, we found a rat that had been electrocuted and cooked across the terminals where the 240 VAC feed from the wall socket connected inside the range.
"A good example of what happens with the latter (self-reset) type can be found in most lamp ballasts: we've all seen fluorescent and other discharge-type lamps that SLOOOOOOOOOWLY cycle on and off all by themselves as the ballast and/or lamp gets old and triggers the device during "normal" operation. It's especially annoying in vapor-discharge (mercury or sodium) street lights (even more so if it's the one right beside you bedroom window!). "
Actually in this case it isn't a reseting cutout but a fundamental property of the gas discharge lamp. As the lamp ages the voltage required to maintain the arc discharge rises, eventually (about 20k-25k hours for HPS lamps, about 3/4 that for mercury & metal halide) reaching a level higher than the max running voltage available from the ballast and the arc extinguishes. The discharge tube then cools to a point that the arc can be restruck by the ballest whereupon the lamp's arc tube reheats and the cycle repears. The solution is to relamp the fixture.
At least your dishes should be super clean as they were being sand blasted as well as washed. The each little chip probably became part of the blasting process. I wonder just how far it would have gone before blowing a hole through the door. Just a thought.
Waxahatchie is about 30 miles due south of Dallas, and certainly would have both fire ants and sandy/shifty soil structure. I suspect part of the "budget problems" was failure to see how expensive solving foundation problems would be! Typical government boondoggle IMHO. Thought so at the time, still do!
I'm afraid neither I nor Google can remember or find anything about that! Try Snopes; sounds like an (non)urban legend! There may have been other reasons. Most of Texas has relatively unstable soil formations (that's why few newer houses have basements, because the codes now require floating slab foundations).
Most transformers of this type need to have such a device to get their UL/CSA approvals. The unfortunate part about this particular one was the manufacturer's choice to use one embedded deep within the windings (presumably at the potential hottest spot), and to use a non-self-resetting one. This unit was potted, so I wasn't about to try to rewind it! A good example of what happens with the latter (self-reset) type can be found in most lamp ballasts: we've all seen fluorescent and other discharge-type lamps that SLOOOOOOOOOWLY cycle on and off all by themselves as the ballast and/or lamp gets old and triggers the device during "normal" operation. It's especially annoying in vapor-discharge (mercury or sodium) street lights (even more so if it's the one right beside you bedroom window!). However, I suppose that's better (from a safety standpoint) than a street light that's out and stays that way!
Some cars are more reliable than others, but even the vehicles at the bottom of this year’s Consumer Reports reliability survey are vastly better than those of 20 years ago in the key areas of powertrain and hardware, experts said this week.
Many of the materials in this slideshow are resins or elastomers, plus reinforced materials, styrenics, and PLA masterbatches. Applications range from automotive and aerospace to industrial, consumer electronics and wearables, consumer goods, medical and healthcare, as well as sporting goods, and materials for protecting food and beverages.
While many larger companies are still reluctant to rely on wireless networks to transmit important information in industrial settings, there is an increasing acceptance rate of the newer, more robust wireless options that are now available.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.