You're right Nancy, I should have included the fridge in my exception list. My main concern used to be the clothes dryer until I heard about all kinds of problems like the one you describe in your dishwasher. So I have a zero-tolerance policy with electric and gas appliances, with the exception of the fridge.
And with all of the fancy electronic features that are being added all of the time, Rob - it will probably get worse. We just bought a washer a few months ago and we no longer set the water level - the washer senses it. I hate to think what will happen if the water level sensor circuitry goes out...
I see what you are saying Ann and it is no doubt excellent practice - but refrigerators run all of the time...and while I don't typically leave the house if appliances are running - I can't say that about the dishwasher which becomes invisible to me after the main wash cycle has completed...until a plastic spoon fell through the top basket and was lodged against the heating element when the heated dry cycle came on - between the burning smell and the smoke coming out of it - that could have ended quite badly. It really is hard to predict all of the scenarios that can happen in a household - especially with two teenagers! LOL I agree - only running appliances while you are home is safest...
Good point, Nancy. In these Made by Monkey blogs, we regularly hear about how the families had washers and dryers for 20 or 30 years with no problem. Then they purchased a new one . . . Seems that the mechanical aspects of the appliances work just fine. But watch out for the electronics.
I never leave the house when an electrical or gas appliance is running. The only exception is the wood stove, which is a lot more reliable, plus there's no off switch anyway (part of the design).
Newer models and control panels...what does that say about this generation of engineering? You would think it would be rock solid and not subject to these issues because of the wealth of experience behind them. Control panels aren't rocket science - I find this A.puzzling and B.concerned about leaving the house if a household appliance is running...
Like naperlou, I've also had good experiences with Kenmore machines and I think their good reputation is well-deserved. Of course, I bought all of mine over 10 years ago, so I'm not sure how well that reputation has lasted. This Made by Monkeys makes me think that perhaps we need a new acronym: DFF (Design-For-Failure), along with all the other DFx designations. This heater layout obviously wasn't DFF-ed.
Good points, Naperlou. One of the questions would be -- how recent is this particular model? Time after time with the Made by Monkeys blog, the problems are with the newer models and their control panels.
In general the Kenmore appliances at very good. We have a washer and dryer (gas) that have lasted a long time and work fine. The issue that you ran into, and your suggestion, make sense. You would think that a company that had been putting out these products for so long would have the engineering knowledge to avoid such problems. This is especially true since it could have been a safety issue.
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
