HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 5/5
naperlou
User Rank
Blogger
Re: cutting one corner too many.
naperlou   5/22/2012 9:06:22 AM
NO RATINGS
This sounds like a common problem with electronics and I think it must be the components. 

I was at the CompUSA warehouse (my son and I go there often).  We are lucky to have this nearby.  The store front is like a factory outlet.  We were looking at building a server, so I was looking at motherboards.  All of them seemed to have a claim that they used Japanese capicators of a certain type.  I wondered at this, since most were made in Taiwan.  After asking around I found that there had been a rash of failures of motherboards a while back, and the cause was cheap capicators.  Sounds like Acer did not get the memo. 

Isn't it interesting that something so basic as a capicator (and its placement) can cause so many problems?

nauzad
User Rank
Silver
Re: cutting one corner too many.
nauzad   5/22/2012 9:01:31 AM
NO RATINGS
I dont remember the brand of capacitors on the board, but I replaced them with Nichikon.

rjnerd
User Rank
Iron
cutting one corner too many.
rjnerd   5/22/2012 7:14:45 AM
NO RATINGS
By any chance were the capacitors branded "LTEC".  If you have a TiVO HR10-250 (the HD DVR that DirecTV distributed)  eventually the thing will start reporting an intermittent overheat condition.  No, its not actually over temp, intstead one or both of the power supply capacitors that are filtering the 5v supply will have the self-same domed top.

Its happened to me on two of them, and if you peruse the Ebay listings of ones offered for parts, you will be sure to find one or two on offer that are also suffering the same problem.  A little time with a soldering iron, and some replacements with a higher temperature rating, and they are fine.

I did notice that the replacement units I bought were noticeably larger than the originals, it was a bit of a squeeze getting them in.  They are located inside an inverted U formed by two of the heat sinks.  They even have one of them in contact with the to-220 case of a switch transistor, and covered with a big blob of glue, that I am sure helps keep them from cooling (hence my grabbing the highest temp spec I could find).

Because the designer packed them in right next to the hottest components on the board, how much was the fault of the capacitor and how much was just due to years of a bake cycle (they don't have an off switch).

<<  <  Page 5/5


Partner Zone
Latest Analysis
Sharon Glotzer and David Pine are hoping to create the first liquid hard drive with liquid nanoparticles that can store 1TB per teaspoon. They aren't the first to find potential data stores, as Harvard researchers have stored 700 TB inside a gram of DNA.
If you see a hitchhiker along the road in Canada this summer, it may not be human. That’s because a robot is thumbing its way across our neighbor to the north as part of a collaborative research project by several Canadian universities.
SpaceX has 3D printed and successfully hot-fired a SuperDraco engine chamber made of Inconel, a high-performance superalloy, using direct metal laser sintering (DMLS). The company's first 3D-printed rocket engine part, a main oxidizer valve body for the Falcon 9 rocket, launched in January and is now qualified on all Falcon 9 flights.
Stanford University researchers have found a way to realize what’s been called the “Holy Grail” of battery-design research -- designing a pure lithium anode for lithium-based batteries. The design has great potential to provide unprecedented efficiency and performance in lithium-based batteries that could substantially drive down the cost of electric vehicles and solve the charging problems associated with smartphones.
UK researchers have come up with a method for machining aerospace-grade, carbon fiber-reinforced composites, along with high-strength aerospace alloys, using an ultrasonically assisted machining device. It also works on high-strength aerospace alloys.
More:Blogs|News
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 18 - 22, Embedded Software Development With Python & the Raspberry Pi
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by igus
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service