I have a Sears reciprocating saw that failed because the drive shaft wore excessivley because the guide was not a traditional bushing, it is an iron casting, AND the manual provided absolutely no information about having to open the case and oil it (there is no oil port, so I didn't even think about it, so I'm partly to blame). And you can't get any replacement parts for any tool more than a couple of years old, I've had to make my own parts.
So, one had better take a good look at a machine before buying as the manufacturer may have been more concerned with their initial profit than the customer's long term satisfaction. And, there may be the calculation done, like Ford did, that dissatisfaction, or death, is a cost that they are willing to bear if failure is below a certain level.
The drive system needs some kind of a slip clutch. The teeth become disengaged well before the drive belt is sufficiently loose to disconnect the engine power. This is how the wheel teeth get chewed up.
That's pretty graphic, Armorris. I agree, the partial engagement is a very natural way of managing the speed of the mower. As a kid a mowed a ton of lawns, and you can't manage a lawn cut with a fully engaged drive (except on long straight stretches). With a fully engaged drive, you can dig ruts into the lawn when you hold back the mower on turns. So you have to slow it down with partial engagement.
As a matter of fact, I had been partially engaging the drive in order to slow down the forward motion of the mower, but that is normal use in my opinion. The engine has a governor and no throttle.
About 45 years ago, in high school, I worked part time for Sears as a TV repairman. Back then, they repaired only Sears products, and at reasonal cost.
My boss told me that Sears made their money on sales and that the service department was the "butt-hole" of the sales department. But if you let the butt-hole get stopped up, you'll see how much it's worth.
@Jaybird2005 I'm always extending the benefit of the doubt to manufacturers, having had to make some tough choices and comprimizes of my own when it comes to development. I didn't own the specific lawn mower in this story, but I would have hoped that if the design was for safety that advertising would have touted it as a positive, advertised this safety "feature", and then provided a spare polymer gear or two with purchase and stocked them in the department store at just over cost...
It does look like 'planned obsolescence', but it might also have been a safety device. If the mower gets up against something solid, like a tree, and the operator (possibly inexperienced) does not release the handle a metal-to-metal gear system may cause damage to the metal gears or cause the mower to bend it's deck or jump in an unexpected way. The existing system would simply strip the plastic gears. It may be better to have the mower stop moving than to risk some other, more severe, damage.
There may have been problems with stones or tree bark getting between the gears and causing severe damage (if they were metal) where the plastic might flex and allow the stones to be ejected with some minor damage to the plastic part rather than a gear grinding halt to the entire system.
The Sears motto for a long time was "We service what we sell." This is great to have a service department, but it would also be great to not need service.
On this particular instance, I wonder if the company didn't anticipate that users would use the mower's driver control to create a slower speed than fully engaged. Sounds like the user was adjusting the engagement lever to slow down the mower, which would mean the gears would grind insted of engaging.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
The 3D printing revolution seems to have a knack for quickly moving technology ahead by way of collaborative effort and even a little friendly competition -- all of course in the name of scientific advancement.
Advantech has launched a new series of motion-control I/O modules to meet the increased demands that come with more distributed industrial systems that require control of a growing number of axes and devices.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
