HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
Page 1/2  >  >>
Nancy Golden
User Rank
Platinum
Re: Doing the digging instead of the quick fix
Nancy Golden   5/18/2012 8:04:15 PM
NO RATINGS
It is interesting naperlou, and something I am always trying to get across. Often times folks don't think twice about changing something material or mechanical and don't expect it to have an impact on the electronics. This story certainly proves otherwise...

DanSchwartz
User Rank
Gold
Send this to Advanced Bionics
DanSchwartz   5/18/2012 4:06:20 PM
NO RATINGS
Somebody needs to forward this to cochlear implant maker Advanced Bionics, which has been struggling to seal their implanted electronics for over a decade, causing losses of upwards a half-billion dollars.

http://TinyURL.com/FailUgly

http://TinyURL.com/FailUgly2

William K.
User Rank
Platinum
Failing sensors mystery
William K.   5/17/2012 9:15:01 PM
NO RATINGS
It appears that on many occasions "epoxy" material is not suited for many kinds of electrical applications. I am aware of some antennas that don't work right when they are insulated with epoxy material, although one would think that they should. Moisture leaching out salts to short circuit a connector is a long way to go, though. It took good troubleshooting skills to find that problem.

ChasChas
User Rank
Platinum
unusual
ChasChas   5/17/2012 10:27:32 AM
NO RATINGS
 

To find the cause first and then the failure process is truly unusual.

Tim
User Rank
Platinum
Moisture Absorption
Tim   5/17/2012 6:52:27 AM
NO RATINGS
The moisture absorption of polyamide is often overlooked in design.  We manufacture a polyamide product that is used on average two years before discard.  Consumers that were keeping the product over the two year mark complained of premature breakage of the product (non-safety related).  Investigation showed that the PA absorbed enough moisture to push out the plasitcizer on the product making it brittle.  As there was no other material available, we opted to put use by dates on the product to guide the consumer to when the products life was ending. 

dboccuti
User Rank
Iron
Re: Secondary or tertiary effects
dboccuti   5/16/2012 8:42:40 PM
NO RATINGS
Thanks for your insightful comment Charles. In this case the change was made for the right reasons (reliability; cost was a secondary benefit) by the system engineering folks, but it had an impact on a sub-system (the sensor) - an unintended consequence. Lesson learned - evaluate everything that might be affected by a change, not just how it affects "your own stuff."

Ann R. Thryft
User Rank
Blogger
Electrical problems are always a hassle
Ann R. Thryft   5/16/2012 6:46:16 PM
NO RATINGS
My only comment is that troubleshooting electrical problems are much harder to diagnose--or even to recognize as such--than mechanical problems.

Charles Murray
User Rank
Blogger
Re: Secondary or tertiary effects
Charles Murray   5/16/2012 6:12:34 PM
NO RATINGS
The interesting aspect of this is that the change was made, not just for cost reduction reasons, but for reliability purposes, as well. It makes me wonder if the original PTFE insulation had a problem, too. Was this a case of replacing something that wasn't working well with something that was even worse? Or was it a case of, "If it ain't broke, don't fix it?"

Jon Titus
User Rank
Blogger
Secondary or tertiary effects
Jon Titus   5/16/2012 12:00:02 PM
NO RATINGS
This story provides a good example of how a secondary effect (insulation change) caused a tertiary effect (shorted contacts).  New engineers must keep these types of problems in mind when they look for the root cause of a defect. That cause isn't always obvious. Nice work.

Rob Spiegel
User Rank
Blogger
Re: Doing the digging instead of the quick fix
Rob Spiegel   5/16/2012 11:08:49 AM
NO RATINGS
Yes, Naperlou, this is a good example of attention to detail. Something as simple as wire insulation made difference between sensors that worked and sensors that failed. This is excellent Sherlock sleuthing.

Page 1/2  >  >>


Partner Zone
Latest Analysis
Just how far has handheld gaming technology come? Let's take a look inside the Nintendo 3DS XL and find out.
Design, simulation, manufacturability, and prototyping: All of these phases are being pushed forward and progressively by underlying technologies.
Wal-Mart will hold its second Made in the USA Open Call July 7-8, at its headquarters in Bentonville, Ark. The event will be a repeat effort by the world’s biggest seller of consumer goods to increase the amount of US-made products it sells in Wal-Mart stores, in Sam’s Club members-only wholesale outlets, and on walmart.com.
From design feasibility, to development, to production, having the right information to make good decisions can ultimately keep a product from failing validation. The key is highly focused information that doesn’t come from conventional, statistics-based tests but from accelerated stress testing.
There’s a good chance that a few of the things mentioned here won't fully come to fruition in 2015 but rather much later down the line. However, as Malcolm X once said, "The future belongs to those who prepare for it today."
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 6 - 10, Building Raspberry Pi Controllers with Python
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service