Interesting to see how supply chains hold up to stress, no doubt about it. As they say, if you're going to put all of your eggs in one basket - then watch that basket! It begs the question as to whether the problem is a supply chain without any breadth of suppliers, or a supply chain in which the suppliers have too much risk. I haven't heard anything about the results of the investigation into the fire in the first place, which might be where the tru problem lies.
TJ, thanks for that comment. I was surprised to learn what a big market share Evonik had, and therefore what a big effect it could have when its plant went offline. I suspect the picture will look pretty different in the next few months.
Thanks, Dave. Like I said, I've seen no mention of EPA requirements. Those could be part of the 5,000 hours of testing, or it might be something already done separately by the materials producers to meet their own automotive standards, since I doubt EPA approval could be achieved in the 3-4 week compressed schedules.
@Ann: Yes, I'm refering to multilayer tubing used for fuel lines. The EPA has regulations regarding evaporative emissions for both automotive and non-automotive applications. Hydrocarbons can permeate through plastic tubing and escape into the atmosphere. It's important to limit this. (This is what our barrier layer does).
I'm not sure what the automotive requirement is, but the marine requirement is 15 grams per square meter per day maximum. This is measured according to one of two SAE standards, depending on whether it is plastic or rubber hose. However, since I'm not directly involved in regulatory compliance, I'm not sure exactly how this needs to be documented to EPA, or what the approval process is.
Dave, EPA requirements were not discussed regarding replacement materials. That said, can you tell us more about the context for the barrier layer you mention? Are you referring to the multi-layer tubing mentioned in the article?
@Ann: Any word on how EPA is handling this with regard to permeation requirements? In our application, there is a barrier layer which is made out of PVDF, not nylon-12, and this barrier layer is not changing. In our design, we rely mainly on this barrier layer (not the nylon-12 itself) to prevent permeation, so we don't expect any problems with EPA approval. But what about in cases where there is no barrier layer?
Tim, thanks for your input. As I reported, DuPont, among others, said that customers began asking for alternatives about two years ago when supply began tightening due to increased demand from solar panel makers and the oil & gas industry. Suppliers may well have begun those efforts even earlier internally. However, the main crunch here is caused by the material's use in automotive manufacturing, where changes in materials do not occur or easily. 5,000 hours, or about 7 months, is the usual required time for testing a new material for fuel lines, the main class of parts affected. This has somehow been fast-tracked down to 3 or 4 weeks by the AIAG's action.
Production of nylon 12 monomer feed stock is extremely difficult and expensive to complete on a large scale. The alternative plans of Dupont and others were most likely completed years ago as an attempt to take market share from Evonik, but they were not cost feasible. Now with end users scrambling to get some sort of alternative material, they are willing to pay a premium for the alternative material and the testing required to qualify it for use.
Dave, thanks for your input. The 40% figure comes from ICIS, the major industry market analyst, so I tend to believe them: http://www.icis.com/Articles/2012/04/30/9554265/news-focus-producers-scramble-to-provide-polyamide-12-alternatives-for-auto.html I agree that it will be very interesting to see if using replacements--and specifically bio-plastic replacements--will continue after the supply of nylon 12 comes back up. There are many other possible replacement products, including Arkema's, but the purpose of the article was not to give a detailed list of alternatives: that's been well covered already in the plastics vertical media and by ICIS.
As energy efficiency becomes more and more a concern for makers of electronics devices, researchers are coming up with new ways to harvest energy from sound vibration, footsteps, and even electromagnetic fields in the air.
The government wants to study your brain, and DARPA wants to use similar information to give robots true autonomy beyond any artificial intelligence developed to date. Sound like science fiction? It's not.
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is