Interesting to see how supply chains hold up to stress, no doubt about it. As they say, if you're going to put all of your eggs in one basket - then watch that basket! It begs the question as to whether the problem is a supply chain without any breadth of suppliers, or a supply chain in which the suppliers have too much risk. I haven't heard anything about the results of the investigation into the fire in the first place, which might be where the tru problem lies.
TJ, thanks for that comment. I was surprised to learn what a big market share Evonik had, and therefore what a big effect it could have when its plant went offline. I suspect the picture will look pretty different in the next few months.
Thanks, Dave. Like I said, I've seen no mention of EPA requirements. Those could be part of the 5,000 hours of testing, or it might be something already done separately by the materials producers to meet their own automotive standards, since I doubt EPA approval could be achieved in the 3-4 week compressed schedules.
@Ann: Yes, I'm refering to multilayer tubing used for fuel lines. The EPA has regulations regarding evaporative emissions for both automotive and non-automotive applications. Hydrocarbons can permeate through plastic tubing and escape into the atmosphere. It's important to limit this. (This is what our barrier layer does).
I'm not sure what the automotive requirement is, but the marine requirement is 15 grams per square meter per day maximum. This is measured according to one of two SAE standards, depending on whether it is plastic or rubber hose. However, since I'm not directly involved in regulatory compliance, I'm not sure exactly how this needs to be documented to EPA, or what the approval process is.
Dave, EPA requirements were not discussed regarding replacement materials. That said, can you tell us more about the context for the barrier layer you mention? Are you referring to the multi-layer tubing mentioned in the article?
@Ann: Any word on how EPA is handling this with regard to permeation requirements? In our application, there is a barrier layer which is made out of PVDF, not nylon-12, and this barrier layer is not changing. In our design, we rely mainly on this barrier layer (not the nylon-12 itself) to prevent permeation, so we don't expect any problems with EPA approval. But what about in cases where there is no barrier layer?
Tim, thanks for your input. As I reported, DuPont, among others, said that customers began asking for alternatives about two years ago when supply began tightening due to increased demand from solar panel makers and the oil & gas industry. Suppliers may well have begun those efforts even earlier internally. However, the main crunch here is caused by the material's use in automotive manufacturing, where changes in materials do not occur or easily. 5,000 hours, or about 7 months, is the usual required time for testing a new material for fuel lines, the main class of parts affected. This has somehow been fast-tracked down to 3 or 4 weeks by the AIAG's action.
Production of nylon 12 monomer feed stock is extremely difficult and expensive to complete on a large scale. The alternative plans of Dupont and others were most likely completed years ago as an attempt to take market share from Evonik, but they were not cost feasible. Now with end users scrambling to get some sort of alternative material, they are willing to pay a premium for the alternative material and the testing required to qualify it for use.
Dave, thanks for your input. The 40% figure comes from ICIS, the major industry market analyst, so I tend to believe them: http://www.icis.com/Articles/2012/04/30/9554265/news-focus-producers-scramble-to-provide-polyamide-12-alternatives-for-auto.html I agree that it will be very interesting to see if using replacements--and specifically bio-plastic replacements--will continue after the supply of nylon 12 comes back up. There are many other possible replacement products, including Arkema's, but the purpose of the article was not to give a detailed list of alternatives: that's been well covered already in the plastics vertical media and by ICIS.
A middle school team from Rochester, Mich., has again nabbed the grand prize in the annual international Future City Competition, which drew students from 37 regions of the United States, as well as from England and China.
The word “smart” is becoming the dumbest word around. It has been applied to almost every device and system in our homes. In addition to smartphones and smart meters, we now hear about smart clothing and smart shoes, smart lights, smart homes, smart buildings, and every trendy city today has its smart city project. Just because it has a computer inside and is connected to the Web, does not mean it is smart.
Are you being paid enough? Do you want a better job? According to a recent survey Manpower released just before Engineers Week, employers and engineers don't see eye-to-eye about the state of US engineers' skills and experience.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.