Instead of worrying about drivers getting killed at 300 MPH, why not start using robotic vehicles? Driving a car around a track provides me with as much amusement as watching grass grow, but for those who enjoy it, a robotic car competition might bring back some of the excitement.
Alcohol as fuel, who knew? I'd rather drink than drive.
If you want to make racing apply to production cars, Let them do anything with the cars but limit them to a fixed number of gallons of fuel to make the 500 miles. Thedn you will see them tune the cars like real world cars with performance per gallon burned as the crieteria.
If you want to make racing apply to production cars, Let them do anything with the cars but limit them to a fixed number of gallons of fuel to make the 500 miles. Thedn you will see them tune the cars like real world cars with performance per gallon burned.
Myron raises an interesting point, but it's bit more difficult to compare than expected. Indy cars run on alchohol, not gasoline, so the power/fuel profiles are different. It also affects cooling and lubrication, since alchohol burns cooleer and 'drier' than gas.
I've been fortunate in my hobby (check my label); one of my friends is a former Indy mechanic, so i know a tiny bit more than most. He got out of it because of the changes in engine rules. He builds engines and is independent - not much for him to do at Indy any more. He spends his time building Bonneville engines and helping build the occaisional friend's personal engine - like mine (grin).
At this point, I think the rules are driven by survivability of the driver. NASCAR has the same issue. They keep choking down the horsepower to a level that keeps the speeed at about 200 on the "super" speedways. Today it might be fairly easy to create a car that would exceed 300 mph on the straights at Indy, but every wreck would kill the driver. So, they are relegated to creating rules that keep the speed down to a relatively survivable 200-230 MPH. This tends to make the competition rather boring at times.
Maybe it would be more interesting if they would opt for some kind of governor system that would simply limit the speed, and allow the teams to decide what power profile to use. For example, some teams might go for a lower power, but higher mileage profile, others for brute acceleration, etc. The high mileage teams would try to make up time by skipping pit stops, and the high power teams would try to make it up out of the corners, etc.
700 horsepower seems a lot, but is it?These engines get these numbers by flowing a lot of fuel and air through the engine.The real question is:how efficiently is that fuel used?Let's see a comparison of stock and various race engines with their brake horsepower per pound of fuel per hour to really judge these engines. Most gasoline engines are about 25% efficient, but I wonder how efficient the present-day Indy engine is?
Another comment: the way the Indy Car series is run, car construction and engine design is so tightly mandated that the "spectacle" is reduced to a "spec racer" series with virtually no room for creativity in these design areas. Gone are the exciting days when a chief mechanic could wave his "magic screwdriver" over the engine or chassis to wring out a few more miles per hour in qualifying. Now we have contrived rules to help make a "show."How about setting a max (but reduced from the gumballs used today) tire width and a maximum front/rear wing area, and max engine displacement, and let the boys and girls have at it.Reduced tire size and downforce-generating wings will mean the drivers will have to lift the throttle to round the turns and thus put driver skill back into the equation.The cars of today have enough of that fabled down force to drive upside down (if you had an inverted road), thus drivers can and do drive flat-out around IMS's four turns.So, let's put more of the driver into the show.I truly love the beautiful Miller cars of the 1920s and 1930s, but their tremendous speed combined with running on steeply banked board tracks produced a high speed parade that left fans bored. Today, Indy cars run in a procession with passing mostly done during fuel and tire stops.Is this racing?Let's hear your thoughts....
That's a really good question, Rob. GM told us that that the tie-in between racing engines and production engines is very strong. A lot of the processes and procedures are carried over from the racing side to the production engine development side. Also, because much of the technology is now the same (i.e., overhead cams; four valves per cylinder; direct injection), both sides can benefit. GM also places an engineer on site at Ilmor Engineering, which engineers the race engine. O'Blenes told us: "Everything he learns will be brought back to help us work on our production products."
Nice article, Chuck. With all of the effort and dollars poured into the development of these high performance engines, is there any spillover into commercial and consumer engines? I would think and automaker would like to get more out of this than doing well at Indy.
This is interesting. These engines use lots of "standard" naterials and parts. On the other hand, they are race engines, so they are tuned up to get maximum horsepower. It is interesting that they are using the smaller block engines. I understand that standardizing on engines cuts costs. I would think though, that for a series that originates in the US would be more into the big block V8. I expect that the cost would be lower with that type of engine.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
