Since other factors, timing, ignition, etc., seem OK, I suspect the problem may be in the fuel system. If this is a fuel injection vehicle, I would check the pressure in the injector fuel rails. If low or non-existent, I would check to see if the in-tank pump is running or the in-tank filter is clogged; remember, if the engine doesn't start, the fuel pump will run only a few seconds. These are not easy to check, I know.
If carbureted, check for (usually mechanical) fuel pump pressure and also the small filter at the fuel inlet to the carburetor. Also, for either fuel system, check the fuel tank evaporative emission controls and fuel tank venting. Without venting the tank won't flow. I would also check the engine air filter as well. And, oh yes, you did check to see if there was fuel in the tank, right??
xti: the gradual loss of power tells me that there is probably an exhaust restriction, such as a clogged catalytic converter. However, I would start by running a comprssion test, and if the compression is OK, then check for exhaust and intake-air restrictions. If compression and airflow are good, then the next step would be to check the air/fuel ratio under power. Ignition timing could also be a concern, and should be checked as well (probably before the fuel mixture) at all RPMs.
Good question, but recall that a test for vibration takes but a few seconds, so starting with a cold engine should not cause any problem at all. Keep in mind that dragsters (top-fuel class cars running nitromethane fuel and superchargers putting out several thousand horsepower) use no coolant at all. Yes, I know they only need to run for the burn-out, staging, and a 5-second race, but as I said, testing for vibration only needs a few seconds.
Timing is good, mechanical advance works as expected. Ignition system checks out OK. (MSD 6A's will easily fire plugs gapped at .150 - even if they're immersed in oil.)
- PS if you ever work on a car that has an MSD ignition - be EXTREMELY careful. NEVER go near the plug wires with the engine running; and NEVER even go near the PRIMARY side of the ignition unless the battery is disconnected. Experience is speaking.
Brakes are fine. Parking brake is fine. Car rolls very easily.
Engine does not miss, backfire, or run rough. Just has no power. Starts easily hot or cold. No strange noises in the engine, no vibrations. Oil pressure is fine. Temp is fine.
So where are all the people that were telling us how they could have found the missing bearing in 15 minutes, and how dumb the mechanics were to be changing all those parts?
C'mon guys - step up and tell us how to fix the Monte Carlo. No wild guesses - only a methodical, reasoned approach is allowed.
I will even give you a hint. Three things that troubleshooters often seem to ignore in favour of a purely technical approach. What, When, and Where. But you have to ask the right questions. Customers rarely recognize that something they did might have caused a problem. Oops, did I just see a cat run out of that bag?
If nobody seems to be getting warm, I'll define exactly what I mean by those terms.
GlennA - thanks for playing along. At least someone has big enough, er, "dual, low-hanging, spheroid" objects to step into the fray.
Altair has released an update of its HyperWorks computer-aided engineering simulation suite that includes new features focusing on four key areas of product design: performance optimization, lightweight design, lead-time reduction, and new technologies.
At IMTS last week, Stratasys introduced two new multi-materials PolyJet 3D printers, plus a new UV-resistant material for its FDM production 3D printers. They can be used in making jigs and fixtures, as well as prototypes and small runs of production parts.
In a line of ultra-futuristic projects, DARPA is developing a brain microchip that will help heal the bodies and minds of soldiers. A final product is far off, but preliminary chips are already being tested.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.