TJ, what is interesting along those lines is that there have not been such sensors employed until now. Sensors will give us a better picture of what the restrictions should be. That and the detection of the clouds and their composition should allow a more fine grained safety zone definition.
When you are going 500-600MPH, by the time the sensor has anything useful to tell you, the Engine has already suffered damage. These sensors would be more useful to help schedule maintainance of the Engines (e.g. knowing when the Engine has suffered enough cumulative wear and tear to need an overhaul).
Radar or Lidar mapping of the area in front of the plane seems much more useful for volcanic damage avoidance. It would let the pilot know that they need to climb or descend to avoid the cloud of debris. Even better, would be satellite mapping of areas or routes to avoid (just like weather, but tuned to detect airborne volcanic debris).
Water or snow entering the engine can be quite impressive. One night (way way back) I was in an airport tower and saw one of the big planes land on a runway that had a light dusting of snow. The explosion out the back of the engine was distressing (at least to me). Not seeing anyone even notice, I asked what had just happened, and they told me that it was a compressor stall from snow sucked up into the engine. Apparently it happens all the time.
This article was very interesting. The choice of materials used as stated in the article: "The cereal and crayons will leave a colorful trail of grains and wax that the researchers can see and study to gauge how well the sensors work." It kind of a "blood splatter pattern" for detecting the efficiency of the sensors. Quite clever if you ask me!
BA flight 9 on June 24, 1982 demonstrated the very real danger; all four engines flamed out after encountering an ash cloud.
This seems like testing for minimum safe exposure to a heavy metal poison. I'd just as soon avoid it completely.
I like the idea of ever better engine damage detection. But there should be some attention paid to detecting hazards such as ash clouds from a distance, to better quantify the reach of the cloud. Instead of shutting down air travel over the entire continent, a much more narrow exlusion zone can be defined to minimize travel disruption while still completely avoiding the cloud.
Rob, I also remember when a lot of those flights were cancelled because of the volcano. I believe one of the big trade shows in Europe lost thousands of attendees because of it. I would imagine that some of the big carriers also lost money as a result of it.
Thanks for writing about this. It's good to see that warning systems for engines are being put into place. Like Beth, I also wonder why these particular materials were used--cereal and crayons. And when it comes to flying, I can't imagine what "over-caution" would mean.
Well, I'm impressed. I remember when all of those flights to and from Europe were cancelled. It's nice to see that someone is looking into improving our ability to detect the volcanic glass -- and thus probably avoid it. I know the flight folks were criticized from over-caution. With the sensors, the airlines will be able to determine whether there is actual danger or not.
Given the recent incidents not only with volanic ash, but planes getting into trouble hitting flocks of birds, this kind of testing is critical. Interesting choice of materials to test with. Any backstory on why cereal and crayons to simulate debris that a plane might encounter mid air?
The 3D printing revolution seems to have a knack for quickly moving technology ahead by way of collaborative effort and even a little friendly competition -- all of course in the name of scientific advancement.
Advantech has launched a new series of motion-control I/O modules to meet the increased demands that come with more distributed industrial systems that require control of a growing number of axes and devices.
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is