The article notes that the quiet hull tumblehome makes the ship "stealthy." But can a ship that size travelling through the sea really be very stealthy? Or is that just a comparative term, i.e., more stealthy than predecessors?
i seriously doubt a rail gun will ever be deployed as a standard weapon as it tends to destroy itself in a few rounds. With all the problems with it guided rockets are a far better weapon.
An the real future weapon should be a low pressure cannon launching guided projectiles or missles we already have, just modied to launch from th 50-80', 24'' dia fixed at 45deg or so gives warheads 100-500 mile range at a % of the cost of a cruise missle.
Next we just can't afford the oil to run these. They need a small nuke like the Hyperion 100Mw heat source steam generator powering the propulsion and house. When docked can supply the base with electric.
Facts are this too big and easily damaged. Better go to a Tri hull with the outer ones protecting the inner one from fighting damage. Other advantages is on a 500' Tri you can do an aircraft carrier as so much deck. Destroyers, Cruiser like above only 250-300' long.
No Navy can bring up 10% of ours so greatly increasing size, numbers, tech makes no sense when smaller, more economical, survivable craft able to put far more ordnance on target farther away run on mini inherently safe nukes would make a better future we might be able to afford.
And maybe a gov that stops starting wars over oil so the navy can do things like diaster relief, etc instead so we might be better received in other lands and less wanting to kill us. Just a thought. PS Saves a lot of money too.
I should think that both the laser and rail gun are line of sight "straight shooting" weapons, while naval battles can be fought over the horizon, so perhaps these are defensive weapons.
@NadineJ I can't see where the military was ever concerned about cost control, why start now ;-)
As for deplying these weapons on older ships, @naperlou had it right - it should not be an issue.
Nice article, Elizabeth. When Bath rattles off details such as "electric drive/integrated power systems, automated ship control and damage control systems, and a totally integrated, ship-wide command and control system," it sounds like a modern factory.
@JDT: I agree. I bet there was and still is a serious simulation aspect to this ship to test all types of conditions whether related to the weather or to different types of at-sea battle scenarios. It would be interesting to inside the war-room of sorts to see what is being conducted.
Naval warships take a lot of beatings, whether it be from Mother Nature, pounding seas, storms, etc. of from NGS. I worry about automation, and builders trying to cut corners to save on the budgets. It will be the crews that pay the price for their oversight.
These ships MUST be tested in all types of conditions to the fullest extent possible, and the longest time possible.
Good question. I'm curious about the cost too. The article says that less manpower can be used in these more powerful vessels. Is the lower payroll balanced out by the higher cost or is there long-term savings?
This next-gen warship is sooner than expected but right on time given that we move faster through cycles-fashion, innovation, etc.-than ever before. It's good to see the navy addressing noise pollution in the ocean.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
The 3D printing revolution seems to have a knack for quickly moving technology ahead by way of collaborative effort and even a little friendly competition -- all of course in the name of scientific advancement.
Advantech has launched a new series of motion-control I/O modules to meet the increased demands that come with more distributed industrial systems that require control of a growing number of axes and devices.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
4 
