We like to make fun of engineers, scientists and their quality departments. However, this could be a case of your young sales person not understanding a new product and trying to sell into the wrong application. Shielded cable needs to have a. Conductive sheath around the signal carrying cable. However, other products exist that are absorbing (not shielding) that can attenuate outside signals. Absorbers are isolated metal (iron or ferrite) particles imbedded in a matrix that is wrapped around the area or cable to be protected or even the area emitting the undesirable frequency.
This might be a case of "sold by monkeys" instraead of "Made by Monkeys".
A few years ago while developing a very sophisticated proof of concept prototype of a laser projection keyboard, I had mistakenly planned for conductive adhesive tape –a tape very similar to the one described here – which was to provide an electrical interconnect signal for one of the finger sensors of the assembly. Being a mechanical engineer, I neglected to consider the high resistance of the conductive adhesive, and the entire design concept was jeopardized because of my lack of experience.I had **assumed** that conductive adhesive would be conductive – and did not consider insufficient conductivity.
The tape was manufactured using Φ.002" conductive spheres potted and floating within a .0015" thick adhesive layer.Surely that would work.But it did not. There was nowhere near enough metal content floating in the adhesive, and the (poor conductivity / high resistance) rendered my entire design concept back to the drawing board.But the experience taught me much about laminates and conductive tapes.
Fast-forward now to is article, and read again, what the Salesman brought in: he said he had a new electrical shielding tape.From the content of the story, his company didn't make any claims about conductivity.
Point being, it really is the design engineers' responsibility to understand completely the characterization of all the elements going into a design.I wouldn't spend too much time slamming the quality of the tape manufacturer.If a component is not suitable for your design, MOVE ON, and find one that is.
I came up against exactly that sort of problem during an analysis of why some sensors were not sensing correctly. The product used connections to a gold alloy plating on each side of a piece of material, except that the coating was nonconductive in that areq, while on some samples it had a high resistance. I quickly developed a test fixture to check the problem, and we discovered a sixty percent yoeild in the coating process. But we did not produce any more deffective parts.
Especially since at the surface this appears to be a faulty design. It's not like the electrical side was 1/2" too short or something. It literally wasn't there.
Mind-boggling is the right word. There's been so many of these kinds of stories in Made by Monkeys lately, I'm starting to wonder if quality control just doesn't exist in some companies anymore.
jmiller, that's what surprises me--that a company manufacturing a safety device can get away with no QA procedures, or at least, not the correct ones that would have caught this. And I think your comment regarding compartmentalization of responsibilities and job functions might go a long way toward explaining how that could happen.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
