HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 4/4
kenish
User Rank
Platinum
Re: No conductivity tests?
kenish   4/27/2012 12:33:38 PM
NO RATINGS
@Ann- LOL, shame on you for not switching hats from Engineering to Sales/Mktg !  The tape is a major breakthrough because it does not need to have sides identified.  Both sides of the tape have equal conductivity.  This saves a lot of time, labor, and chance for error on the production floor.  :)

Phil Hobbs
User Rank
Iron
Throw it over the wall
Phil Hobbs   4/27/2012 11:54:09 AM
NO RATINGS
Sounds like something that worked fine in the lab but was never tested under actual production conditions, e.g. winding onto a large roll.  Plastic stretches; metal films don't.  

It's surprising how little stretching is required to make metal coatings break--I had a fair amount of frustrating experience making thermal imagers out of metallized PVDF film before I switched to carbon-loaded ink.  That stuff was stretchy enough to take a hard crease, and conductive enough for the job.  (There's a war story at http://electrooptical.net/www/footprints/fpwaropn.pdf, and a bit more discussion at http://electrooptical.net#footprints.)

Cheers

Phil Hobbs

jmiller
User Rank
Platinum
Re: Quality Control
jmiller   4/27/2012 9:58:34 AM
NO RATINGS
It sounds to me like quality is reporting to the wrong person.  From the top down, if quality is reporting to operations they will be forced to push it through rather than slow down or stop production making them do it right.  The goal of quality has to be quality and quality only.  And they should report through a different chain of command all the way to the top.  That way the big guy can tell quality to focus on quality and operations to focus on making good products.

Funny how often the products we  put out are dictated by the system that we choose to function in and the directions we are given from the top down.

jmiller
User Rank
Platinum
Re: No conductivity tests?
jmiller   4/27/2012 9:54:50 AM
NO RATINGS
I'm guessing there is no quality control within the manufacturing process.  And for something like  this, which could be used as a safety device, I would think the manufacturer would have to have some on-line testing to prove the product is capable of delivering on the specifications.

jmiller
User Rank
Platinum
Re: So many chances to NOT fail
jmiller   4/27/2012 9:53:29 AM
NO RATINGS
I find this story interesting as well as your reply.  It sounds to me like the design system was broken.  In some companies the lines and definitions on what people are supposed to deliver are so blurry that things get overlooked.  Never quite so big a thing as this.  but still, how often does quality put on their engineering hat and start to solve the engineering problem rather than validating the design.  How often do engineers start talking to vendors because, it's just easier and then I don't have to deal with purchasing.

Great example here of what not to do.  But I think the focus on corrections has to go back to the system and how it failed.

BrainiacV
User Rank
Platinum
Re: Quality Control
BrainiacV   4/27/2012 9:38:00 AM
NO RATINGS
Friends of mine, who worked in quality control, said they were always under pressure to push the stuff out the door.  Flagging bad products impeded productivity.  It would be up to the customer to notice any problem and chances are they would not.

I'd be listening to this with my jaw sagging at the thought this behavior might be typical.

Years later I was upgrading memory in a computer and found that while the computer had worked for several years (expiring the warranty) that it could not work with the higher density memory that the specifications said it could.  Obviously it had not been tested, but they were still able to kick it out the door and make money with it.

One place I worked I later learned typically quoted capabilities about twice what the product was capable of.  Silly me, I had performed some time/motion studies on one system I had installed and estimated it could work at twice the current speed.  The Salesman shushed me when I told him my results because they had sold the system quoting twice that rate.  That behavior finally came back to bite them when a client said, "Show me." before they would sign off on the final payment.  I calculated the system could never achieve the contracted rates. But the blame was placed on our department, rather than the salesman.

 

tekochip
User Rank
Platinum
Quality Control
tekochip   4/27/2012 7:36:39 AM
NO RATINGS
You have to wonder what sort of quality control is employed by the manufacturer.

Rob Spiegel
User Rank
Blogger
Re: So many chances to NOT fail
Rob Spiegel   4/26/2012 2:38:30 PM
NO RATINGS
You're right, TJ, about bad news going viral. There's an old adage that an unhappy customer will tell 20 people about the bad experience, while a happy customer will tell two.

The Internet, of course, amplifies this by a thousandfold.

Ann R. Thryft
User Rank
Blogger
No conductivity tests?
Ann R. Thryft   4/26/2012 2:35:18 PM
NO RATINGS

Wow, this is mind boggling. A tape that's supposed to have one conductive side has no conductive sides. How hard would that be to determine if properly tested for, uh, conductivity? 


TJ McDermott
User Rank
Blogger
So many chances to NOT fail
TJ McDermott   4/26/2012 10:37:51 AM
NO RATINGS
This supplier makes me think of LockMart and the NOAA N-Prime weather satellite fiasco.

In each case, there were so many chances to catch the problem before it became acute.
  • Did engineering do enough tests before hand to prove the theory?
  • Did the tape meet the engineer's design specifications?
  • Did quality control do ANY checks?

These failures directly impact the company's name.  They've at least one customer now who will not trust them, and such an anecdote has a way of going viral.

 

<<  <  Page 4/4


Partner Zone
Latest Analysis
2016 engineering grads can expect to earn an average salary of $65,000 right out of the gate. Petroleum engineers' wallets are much fatter, though -- they are expected to earn about $20K more.
3D printing is now adding value to manufacturers at all steps along the business value chain. Come find out how at a talk by John Jaddou at next month's Embedded Systems Conference in Minneapolis.
From IoT and M2M to flexible robotics and consumer HMI, the advances in smart manufacturing are being deployed on the packaging floor.
These new 3D-printing technologies and printers include some that are truly boundary-breaking: a sophisticated new sub-$10,000, 10-plus materials bioprinter, the first industrial-strength silicone 3D-printing service, and a clever twist on 3D printing and thermoforming for making high-quality realistic models.
Ear-based heart-rate monitoring gained momentum recently, as sensor maker Valencell Inc. announced it has licensed its biometric earpiece technology to Samsung Electronics Co. Ltd for use in so-called “hearable devices.”
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 8 - 12, Getting Hands On with Arduino Mechatronics
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service