HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
Page 1/2  >  >>
Ann R. Thryft
User Rank
Blogger
Re: Too simple for smart
Ann R. Thryft   5/15/2012 5:20:10 PM
NO RATINGS
Sounds like this one could be the source of several Sherlocks.

Rob Spiegel
User Rank
Blogger
Re: Too simple for smart
Rob Spiegel   5/15/2012 4:23:44 PM
NO RATINGS
There was no final fix in this story, Ann. Perhaps we'll see another Sherlock Ohms story in a couple years when the next set of engineers try to figure out this eventual failure.

Ann R. Thryft
User Rank
Blogger
Re: Too simple for smart
Ann R. Thryft   5/15/2012 2:41:14 PM
NO RATINGS
I guess it's more surprising to me that the owner would make another temporary fix after the first one. Was there actually a final fix?

Rob Spiegel
User Rank
Blogger
Re: Too simple for smart
Rob Spiegel   5/14/2012 4:06:57 PM
NO RATINGS
Yes, this is the second temporary repair. In some ways the first temporary repair is the most suprising since it sounds like it was done by the vendor during the installation process.

Ann R. Thryft
User Rank
Blogger
Re: Too simple for smart
Ann R. Thryft   5/14/2012 3:14:16 PM
NO RATINGS
I'm also surprised that a temporary repair was made and not a permanent one, since it appears this is the second temporary repair.

Rob Spiegel
User Rank
Blogger
Re: Too simple for smart
Rob Spiegel   5/9/2012 12:48:24 PM
NO RATINGS
I would guess they went for a permanent stripe, since they would know that the improvised ink line would eventially fail, just as the frist improvised ink line failed.

Charles Murray
User Rank
Blogger
Re: Too simple for smart
Charles Murray   5/4/2012 6:57:11 PM
NO RATINGS
The author notes that this was a "temporary fix." I wonder what he used as a permanent fix.

William K.
User Rank
Platinum
Poor ink impededs CT scanner.
William K.   4/24/2012 10:04:24 PM
NO RATINGS
Insufficient contrast is a very subtle failure mode indeed. The system goes from functioning to intermittant to failed and nothing shows up as the cause. Hartridge has a similar problem with the linear encoders in their fuel injector system teststands, except that it is dirt, not fading. The normal fix is a new encoder for about $450, and two hours wait, and hope the new encoder is in stock. My cheap fix was to clean the scale in the encoder with denatured alcohol and a soft lense wipe tissue. Materials cost is about ten cents and the labor time is about five minutes and no recalibration is needed. But the profit is less, so the customer gets the _____.

Greg M. Jung
User Rank
Platinum
Corrective Action
Greg M. Jung   4/24/2012 9:15:26 PM
NO RATINGS
Good article. 

I guess in today's highly regulated environment, this temporary black pen fix would not be enough.  In addition to solving the problem immediately, a root-cause countermeasure would also be needed to be performed by the equipment manufacturer so this problem would not occur again years later.

Noswad
User Rank
Gold
Shoddy repair work!
Noswad   4/24/2012 4:51:07 PM
NO RATINGS
Sounds like a bad way to repair something. Could they have not repaired the wheel with a permanent solution. They should have replaced the wheel with a new and good one.

If I were their manager, I would not have allowed that type of repair. It will come back to haunt someone else in the future.

Page 1/2  >  >>


Partner Zone
Latest Analysis
From wearables to design changes to rumors of a car, Apple has multiple things cooking up in its kitchen. Here are six possibilities from Apple next week, with likely more than one coming to light.
The key to the success of alt energy is advanced automation, which is still relatively new to the energy scene.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
New fastening and joining methods are making it possible to join multiple materials and thinner sheets in consumer and medical portable electronics, as well as automotive and aviation systems.
An upcoming Digi-Key Continuing Education Center class on designing motor control using MCUs and FPGAs will show you how to choose the best hardware and tools to speed up your development time.
More:Blogs|News
Design News Webinar Series
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Mar 9 - 13, Implementing Motor Control Designs with MCUs and FPGAs: An Introduction and Update
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service