There are many variables such as Ph, temperature (I anticipate room temp), Salinity, turbidity (Clear) etc etc. So best to assume a fairly common standard - fresh water is most common. This could be changed to a certain salinity in 5 or 10 years or so - depending upon how the original design rule 'performs'.
The length of time would be sufficient to ensure manufacturers protected against electrolysis - i.e. not destroying computer and instruments. A short dunking would not test this. All materials should survive 24 hrs in fresh water, tho dissaembly, cleaning, drying etc, new oils, filters etc may be required.
With the extreme weather we have been having, insurance cos have been enjoying 'windfall losses' due to poor design & test procedure of manufacturers, and poor driving choices of drivers.
Yes, I have put quite a bit of thought into this proposal.
& I want to know what happens when an EV car gets dunked - fresh water or salt water. No discussion of this AFAIK. There is potential (pun intended) for electrocution.
I have proposed a new Australian Design Rule that - any - new car (EV too) must survive a 24 hour dunking in fresh water without having to be written off. Sure change oils minor repairs but insurance companies should not be stuck with poor design choices of manufacturer.
I am having a tough time with the sensationalism going on here by engineers and others. The battery is experimental - they were trying to get it to fail - it failed which was the whole point of the test. The test would have been a failure if they did not discover the failure point. Was there some other issue with the test chamber that caused an unexpected buildup of gases - can't say, but that is what the story should be about - and of course those affected by the aftermath. Also, worrying about mechanic working on an electrified car is almost as mis-informed. Cars have been electrified with enough power to kill someone for quite a while. My point is mechanics are trained for these things. The new mechanics will be trained with the same training that electricians receive who work on high voltage systems. Just to be clear, every Volt runs on the same inverter technology that has existed in factories for years. I am not being trite here, it is simply something to be learned not to be feared. So please, stop with the worry wart stuff!
Personally, I think the EV battery dangers are being way overblown. That's one of the problems with today's social media. Have you ever heard of the dangers of the common 12 Vdc or 24 Vdc battery exploding or causing fires? I doubt it and yet it has happened. Back when I was still an automotive mechanic, I was checking over the electrical/charging system of a vehicle that was brought with a hard-to-start problem. The charging and starting systems all checked out which left the battery. When I did a load test on it, the top of the battery blew off. I was fortunate that I was wearing glasses, otherwise I would have had acid in my eyes. As it was, I had to have stitches where the battery top struck my face. My point is this: Everyday we all are in close proximity of items that can hurt us. Our laptops and electronic devices all have lithium ion batteries. They can can explode as well. As one poster pointed out, our cars all have tens of gallons of gas and yet we don't rail about the dangers of that.
Glad to hear that my battery will not explode, but I agree on the voltage danger. First responders had significant concern with the latent voltage of the lithium ion battery stack on EV's when they were introduced. It would be a terrible thing if they needed to use the jaws of life to peel the car away from you after an accident only to be hit with high voltage from the car during the rescue.
I agree Warren. This incident happenened during a factory test. I'm sure there could be other "extreme" tests done on gasoline powered cars that would make them go boom as well (Ford Pinto anyone?). As you mentioned, voltage is a much bigger issue. I used to work in an industry that due to it's nature needed to be extremely safety aware and pretty much everyone was well trained in their jobs. No back-yard mechanics there. You needed to be an card-carrying electrician to work on anything over 24VDC. I worry about somebody who knows just enough to be dangerous trying to fix one of these in his driveway.
Unfortunately, people are notoriously bad at assessing risk, even when given accurate information. Stoking fear by sensationalizing an event doesn't help the situation. To be fair, driving a car is probably the single most dangerous part of anybody's day. Yet, despite the 40,000 deaths a year from this activity (in the U.S.) you don't hear any public outcry.
I am not as worried about the exploding battery issue as I am with the dangers involved to the poor mechanic who has to work on these things. The high voltage can kill! Plus, the computer goes through a systems check periodically and activates, amongst many other things, the brakes. If you are working on the brakes at the time, you might just lose a finger! Mechanic friends of mine are scared of the electric cars. You can't always get a factory tech, so the small-town mechanic might be the highest risk group of all- not Alaskan crab fisherman dangerous- but significant nonetheless.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
The 3D printing revolution seems to have a knack for quickly moving technology ahead by way of collaborative effort and even a little friendly competition -- all of course in the name of scientific advancement.
Advantech has launched a new series of motion-control I/O modules to meet the increased demands that come with more distributed industrial systems that require control of a growing number of axes and devices.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
