View Comments: Newest First|Oldest First|Threaded View
Page 1/2  >  >>
User Rank
I have never heard of that one before
rcwithlime   4/25/2012 2:30:52 PM
I will have to check that out. Very interesting!

Thank you


User Rank
Re: Yes, place multimeter into Diode check mode,
cvandewater   4/25/2012 1:54:22 PM
There is a reason that old fuse holders used the same screw thread as lightbulbs.

When a fuse blew, you put a high wattage bulb in and then tried plugging in/out until you discovered the appliance or cord that caused the bulb to go from "off" to "full on".

With today's breakers it is not so easy to go through a set of fuses and blow them all, then to stop and consider that maybe the fuse was not the problem.

User Rank
Yes, place multimeter into Diode check mode,
rcwithlime   4/25/2012 9:23:23 AM
and listen for the sound. That would identify a short to ground (or shielding if shielded cable, which would then be terminated to ground at the source point.)

I like to use the diode check, as do not have to look at the screen. Using this and the "bundling" technique, and you can soon locate the short. Have done this in many control cabinets.  

Can use Ohm mode to see level of resistance as you described. The light bulb check does help to identify a short as opposed to a flow to ground through another component, but I have seen where using the bulb actually created enough working load that it burned the few wire strands that were contacting the ground, and then went out. Now you measure to ground, and the wires that had shown a short do not, and you have still identified the faulty wire.

Of course, back in the old days, many of us did not have multimeters and it was standard practice to use bulbs for testing, including to trace wires, etc. on our automobiles.

Good postings.

Scott Orlosky
User Rank
Re: Good Job!!!
Scott Orlosky   4/14/2012 7:22:28 PM
I agree.  It's nice to see an example of a well run and methodical investigation into a failure.  So often, someone goes charging off towards a fix without proper information: an approach I've often heard described as "ready"-"shoot"-"aim".  Well done and well described.

William K.
User Rank
short circuit stymies first shift.
William K.   4/11/2012 10:54:16 AM

putting a higher wattage lightbulb is a trick that I was taught way back in the 1950's, when we had fuses at home and it was a great saver. I used that exact technique just this past Monday for servicing a house-wiring compaint that the circuit breaker would not stay reset. 

The faster way to find the short would have been using the "divide and conquer" approach, which would be to split the hundred terminals into two groups and check each for shorts, then split the shorted group in half and check again. Just two checks and disconnecting three places cuts the number of suspects down to 25 from 100. 

Of course, in some machines the switches circuit feed wire is daisy-chained through the remote wiring, which can make it a bit more work because of needing to open remote boxes.

The one other technique that I have seen is to use a hundred watt lamp with a flasher and a clampon ammeter to determine which wire is drawing the current. That method allows for checking groups of wires without any unhooking, which sometimes reconnecting wires can be a pain. 

Of course, good controls design would always separate output device power feeds from sensor switch feeds. That way the E-Stop could switch off all the motion drive functions.

User Rank
Good Job!!!
wbswenberg   4/11/2012 9:42:56 AM
You just taught me something.  I guess I would have used a multmeter and the Ohms setting to check the load.  Other wise a very expensive TDR. 



User Rank
THINKING it through ....
OLD_CURMUDGEON   4/11/2012 9:29:34 AM
User Rank
Re: Proximity sensor
Mydesign   4/11/2012 5:52:05 AM
1 saves
Glenn, that means you have a great analytical and debugging skill. You are a good service engineer.

User Rank
Re: Proximity sensor
GlennA   4/10/2012 12:56:10 PM
Some of the power wires went to operator panels, some to sensors, some to solenoid valves.  Some proxi sensors have an LED indicating the sensor has power, and some others have an LED to indicate it is detecting the target.  Any section of the machine that had LED's on had to be okay.  When I noticed sensors without LED's on, I just had to look more closely at that area.  It just happened that the sensor had obvious damage from weld expulsions, and was in a location where it was readily visible.  If the sensor had been hidden, or there had been another sensor that was also shorted, the story would have been longer.

Rob Spiegel
User Rank
Re: Short Circuit Troubleshooting
Rob Spiegel   4/10/2012 12:42:35 PM
Sounds like you have some great instructors, Gsmith120. This is a consistent theme in the Sherlock Ohms blogs. Logic used with discipline and thoroughness seems to be the specical sauce for solving engineering problems.

Page 1/2  >  >>

Partner Zone
Latest Analysis
Advertised as the "Most Powerful Tablet Under $100," the Kindle Fire HD 6 was too tempting for the team at iFixit to pass up. Join us to find out if inexpensive means cheap, irreparable, or just down right economical. It's teardown time!
The first photos made with a 3D-printed telescope are here and they're not as fuzzy as you might expect. A team from the University of Sheffield beat NASA to the goal. The photos of the Moon were made with a reflecting telescope that cost the research team Ł100 to make (about $161 US).
At Medical Design & Manufacturing Midwest, Joe Wascow told Design News how Optimal Design prototyped a machine that captures the wing-beat of a duck.
The increased adoption of wireless technology for mission-critical applications has revved up the global market for dynamic electronic general purpose (GP) test equipment. As the link between cloud networks and devices -- smartphones, tablets, and notebooks -- results in more complex devices under test, the demand for radio frequency test equipment is starting to intensify.
Much of the research on lithium-ion batteries is focused on how to make the batteries charge more quickly and last longer than they currently do, work that would significantly improve the experience of mobile device users, as well EV and hybrid car drivers. Researchers in Singapore have come up with what seems like the best solution so far -- a battery that can recharge itself in mere minutes and has a potential lifespan of 20 years.
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 20 - 24, How to Design & Build an Embedded Web Server: An Embedded TCP/IP Tutorial
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: 10/28-10/30 11:00 AM
Sponsored by Stratasys
Next Class: 10/28-10/30 2:00 PM
Sponsored by Gates Corporation
Next Class: 11/11-11/13 2:00 PM
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service